Bill, G4WJS I am trying to install version 2.3.0-rc2 on my Mac running Big Sur (11.1). I am following the instructions in the Read Me file. It says at one point: Now re-boot your Mac. This is

Thanks Dave! Made the change earlier today to the frequency, having used Regedit before I knew what I was getting into as the article Dave referenced says you do need to take care and this setting is

Thank you all for the suggestions. It seems it was an issue with the com port, unchecking 'use FIFO buffers' solved the problem.

Getting Windows to synch correctly is straightforward... Set it for hourly synch: http://noosphere.princeton.edu/time.regedit.html Use a time server from a local geographic pool:

Bill I don't have a screen shot, but this is the text: Hamlib error: Communication timed out while opening connection to rig Again, I don't think its a WSTJ-X issue. I think its something in the

George, there are no Hamlib error messages about audio, Hamlib has nothing to do with audio connections between your rig and PC. If you are getting an error message from WSJT-X then please include

Frank, if you are using flrig to control you rig you will not get Hamlib errors in WSJT-X. Please tell us the exact error message, including details, you are getting from WSJT-X? 73 Bill G4WJS.

Good affternoon I have been running a Yaesu FTDX-1200 using flrig for cat contol with WSJT-X and JTAlert for a couple years. I get the occasional hamlib error, but today i encountered something I

Chris, I am having a similar problem with a Hamlig errors using my FT991A. I have WSJT running on my laptop with no issues but it won't run on my main PC - both run Window 7. I can't help you with

Hi, If on the settings on the General tab you have the Calling CQ Forces Call 1st check box checked, it will turn red when you are calling CQ. 73, Sam W2JDB

Hi Ernst Are you in FT8 mode? If so, the frequency table by default only has FT8 frequencies up to and including 144MHz. In other modes, eg JT65, JT4, QRA64 you should have frequencies

At the VHF + frequencies you have to add them to the frequency list in settings before they show up in the main screen list. Jim Bacher, WB8VSU wb8vsu@... https://trc.guru On Dec 26, 2020, at 10:43

Ernst, After you input the frequencies into thefrequency list, did you select the OK to save them? That got me a long timeago. Hi hi. I am using WSJT-X with a IC-9700 just fineon 432 and

Hi Ernst, no one else has reported such an issue, are you sure you are entering the frequencies correctly in MHz? 73 Bill G4WJS.

Hi, I am using version 2.2.0. My problem: the UHF / SHF frequency as defined in Settings -> Frequencies can not be selected in WSJT main window. Only frequencies up to 144MHz are availabe. VHF

I had the exact same thing happen to me last night. Diane K0DSL -- Diane Saunders K0DSL k0dslae@... 763-807-8772

OM, there's little we can help you with if you do not share the error message, including the details. Hint, on MS Windows, if you get message box from WSJT-X, hit Ctrl+C as soon as it appears. That

Hi OM, it is red when it is active. It can be enabled (checked) but inactive (not red) when the application will not respond to a caller. 73 Bill G4WJS.

I've searched the documentation and the operating tips to no avail, in addition to just watching and noodling on it. Why is the Call 1st check box sometimes red and other times black??

Well, the mystery continues. Downloaded Flrig and that now works fine with WSJT. Obviously not ideal but very strange that all the CAT commands work with that and still Hamlib error when trying WSJT