That's exactly what I'm saying, I've been looking for signs for several days and I can't find them. Maybe someone from NA who is relatively close to me and is coming out in fst4 could tell where they

Wilfredo: I did a search for " WSPR Frequencies " and wrote them down. Apparently, FST4 is being done on WSPR frequencies, although I listened last night to 7.0386 MHz and only saw WSPR signals; no

Hi Peter, sorry for the delay replying. I can confirm that there is a regression in WSJT-X v2.3.0 RC1 that causes it not to recover from network connection errors when

Greetings As far as I could understand in the mail, I tried to do what I show in the image I send you, and I didn't get any results. Is there anything else I should do? co6wil Wilfredo from Cuba De:

There is a problem with the first transmission after a TUNE button toggle causes the next cycle transmission to go silent, e.g., not RF although the transmitter is in TX mode. Subsequent transmission

Thanks to all that have responded. As of now the problem is gone without me changing anything. We'll see if it comes back. The bad thing is that one does not know unless someone tells you or you

Paul, SDR console v1. 5 will runSDR IQ and send to Map65, their is a small icon that allows SDR IQ to send at the correct rate 95.xxx Mbps at say 90khz bandwidth. You can send to same pc 127.0.0.1

Just installed the Win64 OpenSSL vl.l.lh 3MB file and fetching is ok thanks 73

Hello, Looking for help getting MAP65 to work with an SDR-IQ or Flex6300. I tried the DAX-IQ output from SmartSDR at 96000 rate. During the contest, the

On 22/10/2020 17:52, Richard White wrote: Hi Dick, using a SignaLink USB interface the USB Audio Codec devices are the correct devices to select for the WSJT-X

Wilfredo, You could post here https://wsprnet.org/drupal/wsprnet/chat Someone will join you or give advice. 73 Alan G4ZFQ

Several users in North American on 40M in this evening using the WSPR frequency BUT transmitting at 2000 Hz and the "F High" setting adjusted to 2000 Hz. Andy K3UK

Greetings. I have downloaded and installed the latest version of WSJT-X with the aim of entering its new digital mode FST4, but I can't see anyone transmitting. I request help to start working in this

I had a problem using WSJT-X and fl-rig with 2 or 3 seconds latency in the software with one of the PTT options (can’t remember which).. I now use PTT by CAT and it generally is immediate. 73

To follow up on the earlier question - and in the spirit of sharing, I have documented what is required, using v2.3.0-rc1, to properly decode FST4W signals that are now being transmitted on the 2200

Set up: FT-450D, long wire off center fed, 100 watts, no rig control, Signalink USB interface. I have used WSJTX for over 1 year with no problems until a few months ago. I have set up the

Diane That issue occasionally comes up with my setup as well. if you look at the lower right corner of your monitor you’ll see the speaker symbol. Click on that and see what the volume slider is

Hi Christer, what you describe is not really possible, the outgoing message timing is determined on in the software, only small extra delays due to latency, e.g. in a rig;s Tx DSP, should be added

YES. The best by a WIDE margin. It is also free and the support is amazing. You would not be sorry to use this. As said , you need not install all but I would suggest using COMMANDER and Spot

IC-7100 FT8 transmit timing problem. When transmitting the timing (DT) is off by up to 3 sec. (varies). Receiving is no problem. Not an RFI issue. Both stations running low power into dummy