We are trying to use the K3S its USB port communication for WSJT-x modes. For 10Ghz and up it is essential that the K3S will allow changing its frequencies during TX to compensate for the fast moving

Paul I can only use SDR Console v1. 5 with the SDR IQ, the later versions do not seem to support SDR IQ with the correct sampling rate. If I am wrong then I am sure sonebody will correct me and I

Hi David, My version 1.5 says license invalid when I try to run it. Can I use version 2.3 or version 3 which do run OK. If so, how do I do it. I found More options/data repeater under

thanks bill i put the use TCPIP connection setting on the other day and it has been fine since then 73 peter M7PGW On Fri, 23/10/2020 14:07,

Are you using VOX? If so, could the problem be that the VOX is causing the delayed transmission? Try adjusting VOX sensitivity or try using PTT instead.

Greetings again. someone to send me in images how I configure my wsjt-x to receive and transmit in FSt4, I am feeding myself with their theoretical knowledge in this aspect, but I can't hear anyone in

Bill, there was an email sent out last night that reported that FST4 was using WSPR frequencies on 40 meters, but that the audio frequency of 2000 hz was used, which should mean that it would not

David, a QSO mode like FST4 should not be used in WSPR sub-bands, the only exception to this might be on LF and MF bands where often transmitters have very limited bandwidths,

Using 2.2.2 0d9b96 -closed twice (which is this thread - understood fixed in next release) -didn't auto answer when the FOX called me -didn't shift freq when called -didn't turn off ENABLE when FOX

That's exactly what I'm saying, I've been looking for signs for several days and I can't find them. Maybe someone from NA who is relatively close to me and is coming out in fst4 could tell where they

Wilfredo: I did a search for " WSPR Frequencies " and wrote them down. Apparently, FST4 is being done on WSPR frequencies, although I listened last night to 7.0386 MHz and only saw WSPR signals; no

Hi Peter, sorry for the delay replying. I can confirm that there is a regression in WSJT-X v2.3.0 RC1 that causes it not to recover from network connection errors when

Greetings As far as I could understand in the mail, I tried to do what I show in the image I send you, and I didn't get any results. Is there anything else I should do? co6wil Wilfredo from Cuba De:

There is a problem with the first transmission after a TUNE button toggle causes the next cycle transmission to go silent, e.g., not RF although the transmitter is in TX mode. Subsequent transmission

Thanks to all that have responded. As of now the problem is gone without me changing anything. We'll see if it comes back. The bad thing is that one does not know unless someone tells you or you

Paul, SDR console v1. 5 will runSDR IQ and send to Map65, their is a small icon that allows SDR IQ to send at the correct rate 95.xxx Mbps at say 90khz bandwidth. You can send to same pc 127.0.0.1

Just installed the Win64 OpenSSL vl.l.lh 3MB file and fetching is ok thanks 73

Hello, Looking for help getting MAP65 to work with an SDR-IQ or Flex6300. I tried the DAX-IQ output from SmartSDR at 96000 rate. During the contest, the

On 22/10/2020 17:52, Richard White wrote: Hi Dick, using a SignaLink USB interface the USB Audio Codec devices are the correct devices to select for the WSJT-X

Wilfredo, You could post here https://wsprnet.org/drupal/wsprnet/chat Someone will join you or give advice. 73 Alan G4ZFQ