Several users in North American on 40M in this evening using the WSPR frequency BUT transmitting at 2000 Hz and the "F High" setting adjusted to 2000 Hz. Andy K3UK

Greetings. I have downloaded and installed the latest version of WSJT-X with the aim of entering its new digital mode FST4, but I can't see anyone transmitting. I request help to start working in this

I had a problem using WSJT-X and fl-rig with 2 or 3 seconds latency in the software with one of the PTT options (can’t remember which).. I now use PTT by CAT and it generally is immediate. 73

To follow up on the earlier question - and in the spirit of sharing, I have documented what is required, using v2.3.0-rc1, to properly decode FST4W signals that are now being transmitted on the 2200

Set up: FT-450D, long wire off center fed, 100 watts, no rig control, Signalink USB interface. I have used WSJTX for over 1 year with no problems until a few months ago. I have set up the

Diane That issue occasionally comes up with my setup as well. if you look at the lower right corner of your monitor you’ll see the speaker symbol. Click on that and see what the volume slider is

Hi Christer, what you describe is not really possible, the outgoing message timing is determined on in the software, only small extra delays due to latency, e.g. in a rig;s Tx DSP, should be added

YES. The best by a WIDE margin. It is also free and the support is amazing. You would not be sorry to use this. As said , you need not install all but I would suggest using COMMANDER and Spot

IC-7100 FT8 transmit timing problem. When transmitting the timing (DT) is off by up to 3 sec. (varies). Receiving is no problem. Not an RFI issue. Both stations running low power into dummy

Because that is not the purpose of WSJT-X. It provides a rudimentary text log file, but third-party log programs, and software bridges do a much better job than trying to add all sorts

As listed in the WSJT-X User Guide's Windows installation requirements: https://physics.princeton.edu/pulsar/K1JT/wsjtx-doc/wsjtx-main-2.2.2.html#INSTALL_WIN Neil, KN3ILZ

From your screen capture, it appears that your waterfall zero slider and waterfall gain slider are too far to the right. Mine run about the 3rd bar from the left of the scale. The RF Gain on the

LOG4OM v2 works well and is free. www.log4om.com LOGic 9 from PDA is a commercial product that also works well www.hosenose.com/logic -- Anthony Luscre K8ZT Ohio Section Section Youth Coordinator &

Why does wsjt-x not include automatic logging to LoTW, QRZ, etc? I suppose the answer is "because there are other apps that do that so why expend the effort?". That's a reasonable answer but the

Which Open-SSL file and its download location? David VA3MJR On 2020-10-22 3:52 a.m., neil_zampella wrote: --

Tom See here https://www.physics.princeton.edu/pulsar/k1jt/wsjtx.html for the deb install package wsjtx_2.2.2_amd64.deb. However WSJT-X V2.2.2 wont work on Linux Mint 18.x as that is

Um ... the program is up to 2.2.2 with a new release candidate 2.3.0-RC1. Try upgrading? Then have you installed the proper Open-SSL file as I'm assuming you're on

Hi. Fetching doesn't work even I have downoladed the file from ARRL the same mentioned before error message persists.

Perhaps unchecking Call 1st would help in that version. 73, Reino OH3mA

Thanks Al that was the clue I needed. I reduced the IC 7300 RF gain to 40 dB on the Receiving bar graph and the waterfall was restored. The problem seemed to happen by itself. It’s fixed now Thanks