|
locked
Re: Windows 10 -WSJT-X power slider help...
Dave_G0WBX
If you have no choice but to hook a "Speaker" output to a "Mic" input,
you NEED to build a simple resistive attenuator, say 10k in series with the speaker output*, and 100r across the mic input. (Just ballpark values based on what I've done in the past. (* Some, speaker outputs, need a low resistance to bias correctly, so put some 47 ohms across the speaker output too.) If you can't get enough level, lower the value of the 10k, if it's still too hot, increase the value. With care, such things can be built into the interconnecting lead, but label it so you know what it is for in the future. (Don't ask!) 73. Dave G0WBX. -- Created on and sent from a Unix like PC running and using free and open source software:
|
|
|
|
locked
Re: Wide Window Graph
Roger N1RJ <n1rj@...>
Thanks, guys. I see now that it's a combination of window width
toggle quoted messageShow quoted text
and the Bins/pixel setting. It's a bit confusing at first! 73, Roger
On 7/24/2019 1:28 PM, groups@... wrote:
On 24/07/2019 17:54, Gary - AC6EG via Groups.Io wrote:On Wed, Jul 24, 2019 at 06:53 AM, Michael Black wrote:I sometimes see people just below 200 Hz.You need to use your mouse to put a checkmark in the box next to "Controls" in the upper left corner of the wide graph display, then you will be able to see the adjustments you can make to the graph. I have Bins/Pixel set at 4 and have Start set at 200, so my graph runs from 200 Hz to 3500 Hz.
|
|
|
|
locked
Re: Wide Window Graph
Roger
On 24/07/2019 17:54, Gary - AC6EG via Groups.Io wrote:
On Wed, Jul 24, 2019 at 06:53 AM, Michael Black wrote:I sometimes see people just below 200 Hz.You need to use your mouse to put a checkmark in the box next to "Controls" in the upper left corner of the wide graph display, then you will be able to see the adjustments you can make to the graph. I have Bins/Pixel set at 4 and have Start set at 200, so my graph runs from 200 Hz to 3500 Hz. 73, Roger, G4HZA
|
|
|
|
locked
Re: Wide Window Graph
Gary - AC6EG <gdefeyter@...>
On Wed, Jul 24, 2019 at 06:53 AM, Michael Black wrote:
You need to use your mouse to put a checkmark in the box next to "Controls" in the upper left corner of the wide graph display, then you will be able to see the adjustments you can make to the graph. I have Bins/Pixel set at 4 and have Start set at 200, so my graph runs from 200 Hz to 3500 Hz. 73 de Gary - AC6EG
|
|
|
|
locked
Re: Installed 2.1.0 64 bit and now getting "Rig Control Error"
Bob Revel
I think Mike probably has the correct info. Bob KD6C
https://www.dxengineering.com/parts/DXE-CSB-750P
From: WSJTX@groups.io [mailto:WSJTX@groups.io] On Behalf Of Michael Black via Groups.Io
Sent: Tuesday, July 23, 2019 8:28 PM To: WSJTX@groups.io Subject: Re: [WSJTX] Installed 2.1.0 64 bit and now getting "Rig Control Error"
Mix 31 is the common one you'll find.
de Mike W9MDB
On Tuesday, July 23, 2019, 08:59:45 PM CDT, Jerome Sodus <jsodus@...> wrote:
To Bob KD6C, Might you have the mix# of the toroids used? 73 jerry km3k
Sent from my Samsung Galaxy smartphone.
-------- Original message -------- From: Bob Revel <KD6C.ham@...> Date: 7/22/19 14:52 (GMT-05:00) To: WSJTX@groups.io Subject: Re: [WSJTX] Installed 2.1.0 64 bit and now getting "Rig Control Error"
I had a similar issue, whereby I started losing connection (randomly) between my laptop/radio/SignaLink. This might be the issue you are having. Bob, KD6C
From: WSJTX@groups.io [mailto:WSJTX@groups.io] On Behalf Of Bill
Sounds like it but its not. It really is random, no set time.
Sometimes it does not do it for days, I suspect if might be hardware (old computer) and/or me hitting a USB cable accidentally.
Bill K2WH
From: WSJTX@groups.io [mailto:WSJTX@groups.io] On Behalf Of John Kludt
Bill,
Sounds like your USB port is going tot sleep. Make sure you don't have the power saving option on the shuts off the USB port after a given amount of time.
John
On Sun, Jul 21, 2019 at 8:36 PM Bill <k2wh@...> wrote:
-=-=-=-=-=-=-=-=-=-=-=-
|
|
|
|
locked
Re: Windows 10 -WSJT-X power slider help...
Jim Dawson
Thanks,Bill. I'll give it a try.
73 de Jim - K9dd
|
|
|
|
locked
Re: Wide Window Graph
Michael Black
Bins/Pixel. de Mike W9MDB
On Wednesday, July 24, 2019, 08:51:01 AM CDT, Roger N1RJ <n1rj@...> wrote:
Is it possible to adjust the frequency span independently of the window width? I can't seem to do it. 73, Roger -=-=-=-=-=-=-=-=-=-=-=-Groups.io Links: You receive all messages sent to this group. View/Reply Online (#3737): https://groups.io/g/WSJTX/message/3737 Mute This Topic: https://groups.io/mt/32584244/212453 -=-=- Moderated by Andy K3UK and Roger G4HZA -=-=- Group Owner: WSJTX+owner@groups.io Unsubscribe: https://groups.io/g/WSJTX/leave/4118746/1473993136/xyzzy [mdblack98@...] -=-=-=-=-=-=-=-=-=-=-=-
|
|
|
|
locked
Wide Window Graph
Roger N1RJ <n1rj@...>
Is it possible to adjust the frequency span independently
of the window width? I can't seem to do it. 73, Roger
|
|
|
|
locked
Re: Windows 10 -WSJT-X power slider help...
No, never saw that in any U-tube instructions or anywhere mentioned on Yaesu group. But thanks, and I'll give it a try. You have been most helpful in steering me in the right directions. Thanks again, Herb
On July 24, 2019 at 12:28 AM "Michael Black via Groups.Io" <mdblack98@...> wrote:
-=-=-=-=-=-=-=-=-=-=-=-
|
|
|
|
locked
Re: Windows 10 -WSJT-X power slider help...
Thanks Mike.......will adjust. Knew it was way off, but was trying to follow the instructions advice, and wondered what I was missing.
On July 24, 2019 at 12:33 AM "Michael Black via Groups.Io" <mdblack98@...> wrote:
-=-=-=-=-=-=-=-=-=-=-=-
|
|
|
|
locked
Re: Windows 10 -WSJT-X power slider help...
Michael Black
Also...if you're hooking up a speaker output to a MIC input that's a speaker level signal into a mic level input. You're over driving the heck out of it and that's a very common source of harmonics and why your ALC is going nuts. You can turn down the playback level in Windows a LOT. Mike
On Tuesday, July 23, 2019, 11:23:30 PM CDT, Herb Blue <WB8ASI@...> wrote:
set menu 079 to zero, and still blasting ALC with PWR slider at bottom. You got me on the right track tho. I can crank down on the sound card, but the instructions said 0db which is the max. I would use USB if you have any ideas on how to make it work. Got the CP210x Windows Driver installed, and CAT works just fine. Instructions said that WIndows generic USB audio CODEC would install automagically, but a no go. I'm OK with my audio cable work- around, but always wondered why my USB connection never activated. Have had instant success with USB connection with Kenwood 590SG. Just want to confirm that the goal is to have no ALC???? I can make it right with various adjustments, but instructions seem so easy, and it's not that clean. Again, thanks for your help. 73, Herb On July 23, 2019 at 11:55 PM "Michael Black via Groups.Io" <mdblack98@...> wrote:
-=-=-=-=-=-=-=-=-=-=-=-
Groups.io Links: You receive all messages sent to this group. View/Reply Online (#3732): https://groups.io/g/WSJTX/message/3732 Mute This Topic: https://groups.io/mt/32576482/212453 -=-=- Moderated by Andy K3UK and Roger G4HZA -=-=- Group Owner: WSJTX+owner@groups.io Unsubscribe: https://groups.io/g/WSJTX/leave/4084689/1473993136/xyzzy [mdblack98@...] -=-=-=-=-=-=-=-=-=-=-=-
|
|
|
|
locked
Re: Windows 10 -WSJT-X power slider help...
Michael Black
For the USB audio did you set menu 103 to DATA? Mike
On Tuesday, July 23, 2019, 11:23:30 PM CDT, Herb Blue <WB8ASI@...> wrote:
set menu 079 to zero, and still blasting ALC with PWR slider at bottom. You got me on the right track tho. I can crank down on the sound card, but the instructions said 0db which is the max. I would use USB if you have any ideas on how to make it work. Got the CP210x Windows Driver installed, and CAT works just fine. Instructions said that WIndows generic USB audio CODEC would install automagically, but a no go. I'm OK with my audio cable work- around, but always wondered why my USB connection never activated. Have had instant success with USB connection with Kenwood 590SG. Just want to confirm that the goal is to have no ALC???? I can make it right with various adjustments, but instructions seem so easy, and it's not that clean. Again, thanks for your help. 73, Herb On July 23, 2019 at 11:55 PM "Michael Black via Groups.Io" <mdblack98@...> wrote:
-=-=-=-=-=-=-=-=-=-=-=-
Groups.io Links: You receive all messages sent to this group. View/Reply Online (#3732): https://groups.io/g/WSJTX/message/3732 Mute This Topic: https://groups.io/mt/32576482/212453 -=-=- Moderated by Andy K3UK and Roger G4HZA -=-=- Group Owner: WSJTX+owner@groups.io Unsubscribe: https://groups.io/g/WSJTX/leave/4084689/1473993136/xyzzy [mdblack98@...] -=-=-=-=-=-=-=-=-=-=-=-
|
|
|
|
locked
Re: Windows 10 -WSJT-X power slider help...
set menu 079 to zero, and still blasting ALC with PWR slider at bottom. You got me on the right track tho. I can crank down on the sound card, but the instructions said 0db which is the max. I would use USB if you have any ideas on how to make it work. Got the CP210x Windows Driver installed, and CAT works just fine. Instructions said that WIndows generic USB audio CODEC would install automagically, but a no go. I'm OK with my audio cable work- around, but always wondered why my USB connection never activated. Have had instant success with USB connection with Kenwood 590SG. Just want to confirm that the goal is to have no ALC???? I can make it right with various adjustments, but instructions seem so easy, and it's not that clean. Again, thanks for your help. 73, Herb
On July 23, 2019 at 11:55 PM "Michael Black via Groups.Io" <mdblack98@...> wrote:
-=-=-=-=-=-=-=-=-=-=-=-
|
|
|
|
locked
Re: Windows 10 -WSJT-X power slider help...
Michael Black
In which case you probably want the MIC level adjustment menu 079 I figure you were using the USB. de Mike W9MDB
On Tuesday, July 23, 2019, 10:51:01 PM CDT, Herb Blue <WB8ASI@...> wrote:
Thanks Detective Mike........I didn't mention I'm running a FTdx5000, but menu 070 doesn't help even set to zero. I have audio running from computer via cable into rig via rear MIC jack, and from rig rear AV out jack to computer mic jack. (never figured out how to make USB audio CODEC to work on this rig). Has worked good for me a long time. Now difficult figuring out how to use PWR slider with 64-bit install. Seems way off normal, but I'm making QSO's. Any suggestions are most welcome, and others reading this will also benefit. That's how I've learned how to even get started with this computer stuff. I'll look at my menu choices if there is another setting that needs changing. 73 and thanks again, Herb WB8ASI On July 23, 2019 at 11:34 PM "Michael Black via Groups.Io" <mdblack98@...> wrote:
-=-=-=-=-=-=-=-=-=-=-=-
Groups.io Links: You receive all messages sent to this group. View/Reply Online (#3730): https://groups.io/g/WSJTX/message/3730 Mute This Topic: https://groups.io/mt/32576482/212453 -=-=- Moderated by Andy K3UK and Roger G4HZA -=-=- Group Owner: WSJTX+owner@groups.io Unsubscribe: https://groups.io/g/WSJTX/leave/4084689/1473993136/xyzzy [mdblack98@...] -=-=-=-=-=-=-=-=-=-=-=-
|
|
|
|
locked
Re: Windows 10 -WSJT-X power slider help...
Thanks Detective Mike........I didn't mention I'm running a FTdx5000, but menu 070 doesn't help even set to zero. I have audio running from computer via cable into rig via rear MIC jack, and from rig rear AV out jack to computer mic jack. (never figured out how to make USB audio CODEC to work on this rig). Has worked good for me a long time. Now difficult figuring out how to use PWR slider with 64-bit install. Seems way off normal, but I'm making QSO's. Any suggestions are most welcome, and others reading this will also benefit. That's how I've learned how to even get started with this computer stuff. I'll look at my menu choices if there is another setting that needs changing. 73 and thanks again, Herb WB8ASI
On July 23, 2019 at 11:34 PM "Michael Black via Groups.Io" <mdblack98@...> wrote:
-=-=-=-=-=-=-=-=-=-=-=-
|
|
|
|
locked
Re: Windows 10 -WSJT-X power slider help...
Michael Black
Go to menu 070 and turn it down. You can likely crank the Pwr slider all the way up with menu 070 being the adjustment you need to make. de Mike W9MDB
On Tuesday, July 23, 2019, 08:20:42 PM CDT, Herb Blue <WB8ASI@...> wrote:
Thanks Bill, I've just spent the last few days changing from a Windows 7 32-bit PC to one that's WIndows 10 64-bit including upgrading to WSJT-X v2.1.0 and JTAlert 2.13.10, while bringing along my LOG4OM. Whew, couldn't have made it without all I've learned here on-line from everyone's experiences. Now ;you're procedure on volume control is the finishing touch. I've got the device and WSJT-X set at 0db (didn't even know about volume mixer, but I found it). Now I can hardly keep the level down to keep from seeing ALC on the meter even with the PWR slider at the bottom. I liked it better with 32-bit where I could tweak the PWR slider mid-range to just see the meter movement on ALC. Am I understanding your procedure correctly??? Thanks and 73, Herb. WB8ASI Groups.io Links: You receive all messages sent to this group. View/Reply Online (#3726): https://groups.io/g/WSJTX/message/3726 Mute This Topic: https://groups.io/mt/32576482/212453 -=-=- Moderated by Andy K3UK and Roger G4HZA -=-=- Group Owner: WSJTX+owner@groups.io Unsubscribe: https://groups.io/g/WSJTX/leave/4084689/1473993136/xyzzy [mdblack98@...] -=-=-=-=-=-=-=-=-=-=-=-
|
|
|
|
locked
Re: Installed 2.1.0 64 bit and now getting "Rig Control Error"
Michael Black
Mix 31 is the common one you'll find. de Mike W9MDB
On Tuesday, July 23, 2019, 08:59:45 PM CDT, Jerome Sodus <jsodus@...> wrote:
To Bob KD6C, Might you have the mix# of the toroids used? 73 jerry km3k Sent from my Samsung Galaxy smartphone. -------- Original message -------- From: Bob Revel <KD6C.ham@...> Date: 7/22/19 14:52 (GMT-05:00) To: WSJTX@groups.io Subject: Re: [WSJTX] Installed 2.1.0 64 bit and now getting "Rig Control Error" I had a similar issue, whereby I started losing connection (randomly) between my laptop/radio/SignaLink. This might be the issue you are having. Bob, KD6C
From: WSJTX@groups.io [mailto:WSJTX@groups.io] On Behalf Of Bill
Sounds like it but its not. It really is random, no set time.
Sometimes it does not do it for days, I suspect if might be hardware (old computer) and/or me hitting a USB cable accidentally.
Bill K2WH
From: WSJTX@groups.io [mailto:WSJTX@groups.io] On Behalf Of John Kludt
Bill,
Sounds like your USB port is going tot sleep. Make sure you don't have the power saving option on the shuts off the USB port after a given amount of time.
John
On Sun, Jul 21, 2019 at 8:36 PM Bill <k2wh@...> wrote:
-=-=-=-=-=-=-=-=-=-=-=- Groups.io Links: You receive all messages sent to this group. View/Reply Online (#3727): https://groups.io/g/WSJTX/message/3727 Mute This Topic: https://groups.io/mt/32551707/212453 -=-=- Moderated by Andy K3UK and Roger G4HZA -=-=- Group Owner: WSJTX+owner@groups.io Unsubscribe: https://groups.io/g/WSJTX/leave/4084689/1473993136/xyzzy [mdblack98@...] -=-=-=-=-=-=-=-=-=-=-=-
|
|
|
|
locked
Re: Installed 2.1.0 64 bit and now getting "Rig Control Error"
Jerome Sodus
To Bob KD6C, Might you have the mix# of the toroids used? 73 jerry km3k Sent from my Samsung Galaxy smartphone.
-------- Original message -------- From: Bob Revel <KD6C.ham@...> Date: 7/22/19 14:52 (GMT-05:00) To: WSJTX@groups.io Subject: Re: [WSJTX] Installed 2.1.0 64 bit and now getting "Rig Control Error" I had a similar issue, whereby I started losing connection (randomly) between my laptop/radio/SignaLink. This might be the issue you are having. Bob, KD6C
From: WSJTX@groups.io [mailto:WSJTX@groups.io] On Behalf Of Bill
Sounds like it but its not. It really is random, no set time.
Sometimes it does not do it for days, I suspect if might be hardware (old computer) and/or me hitting a USB cable accidentally.
Bill K2WH
From: WSJTX@groups.io [mailto:WSJTX@groups.io] On Behalf Of John Kludt
Bill,
Sounds like your USB port is going tot sleep. Make sure you don't have the power saving option on the shuts off the USB port after a given amount of time.
John
On Sun, Jul 21, 2019 at 8:36 PM Bill <k2wh@...> wrote:
|
|
|
|
locked
Re: Windows 10 -WSJT-X power slider help...
Thanks Bill, I've just spent the last few days changing from a Windows 7 32-bit PC to one that's WIndows 10 64-bit including upgrading to WSJT-X v2.1.0 and JTAlert 2.13.10, while bringing along my LOG4OM. Whew, couldn't have made it without all I've learned here on-line from everyone's experiences. Now ;you're procedure on volume control is the finishing touch. I've got the device and WSJT-X set at 0db (didn't even know about volume mixer, but I found it). Now I can hardly keep the level down to keep from seeing ALC on the meter even with the PWR slider at the bottom. I liked it better with 32-bit where I could tweak the PWR slider mid-range to just see the meter movement on ALC. Am I understanding your procedure correctly??? Thanks and 73, Herb. WB8ASI
|
|
|
|
locked
Re: Windows 10 -WSJT-X power slider help...
On 23/07/2019 21:49, W7CD John wrote:
Hi John, it's good that the DAX devices will not add digital gain. VAC can but also can be disabled in that case. You should get exactly the same power output between the 32-bit and 64-bit versions of WSJT-X if the Windows mixer control for WSJT-X on the DAX Tx speaker device is set to maximum (this is based on your assurance that the DAX input devices have no digital gain). You are missing something when carrying out the procedure above is you are not. Once the one off procedure above has been executed the WSJT-X "Pwr" slider should behave the same for either version although you may find the granularity of steps slightly different and there may be some small discontinuities as you slide the "Pwr" control up and down with the 64-bit. 73
|
|
|