Date   

locked Re: IC 705 CRASHES WSJT-X WHEN TX #band #AudioIssues #Icom

Gary trock
 

Good advice!!

On Nov 28, 2021, at 1:47 PM, Jim Shorney <jshorney@...> wrote:


Brew a pot of coffee and give this a read:

https://na01.safelinks.protection.outlook.com/?url=http%3A%2F%2Faudiosystemsgroup.com%2FRFI-Ham.pdf&;data=04%7C01%7C%7C5fd6919e02f94d778d2408d9b2b8b91b%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C637737328713072828%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C3000&amp;sdata=p%2FeboNPntEIKR3CKAZxstGyT1Pv0STZnCZF7Z4YD6r0%3D&amp;reserved=0

73

-Jim
NU0C

On Sun, 28 Nov 2021 13:10:32 -0800
"Mark Gottlieb" <kk2l@...> wrote:

Good Afternoon All,

I am having this same problem but only from 18mhz on up. On 14mhz down, the rig (IC7100) interfaces normally and well with WSJT-x and FLRIG. Icom radios do have a one USB cable, as we all know, for CAT and AUDIO. Is my issue attributable to the same reasons as the failure others are experiencing? I have tried changing antennas, taking the tuner out of the mix, changing USB cables but the problem persists. Any help would be most appreciated.

73
Mark
KK2L



locked Re: IC 705 CRASHES WSJT-X WHEN TX #band #AudioIssues #Icom

Jim Shorney
 

Brew a pot of coffee and give this a read:

http://audiosystemsgroup.com/RFI-Ham.pdf

73

-Jim
NU0C

On Sun, 28 Nov 2021 13:10:32 -0800
"Mark Gottlieb" <kk2l@...> wrote:

Good Afternoon All,

I am having this same problem but only from 18mhz on up.  On 14mhz down, the rig (IC7100) interfaces normally and well with WSJT-x and FLRIG.  Icom radios do have a one USB cable, as we all know, for CAT and AUDIO.  Is my issue attributable to the same reasons as the failure others are experiencing?  I have tried changing antennas, taking the tuner out of the mix, changing USB cables but the problem persists.  Any help would be most appreciated.

73
Mark
KK2L


locked Re: Version 2.5 trouble #Windows10 #transmit #Kenwood

Dave
 

Yes I did the double click to put him in the TX window.

For some reason the RX station or any station I try does not answer which is strange.

Dave KC3AM

On 11/27/2021 3:53 PM, Dave Garber wrote:
you did click on him replying, right.   
Dave Garber
VE3WEJ / VE3IE


On Sat, Nov 27, 2021 at 3:10 PM Sam Birnbaum via groups.io <w2jdb=aol.com@groups.io> wrote:
Make sure you have the Call1st check box checked.

Sam W2JDB



-----Original Message-----
From: Dave via groups.io <kc3am=verizon.net@groups.io>
To: main@WSJTX.groups.io
Sent: Sat, Nov 27, 2021 2:55 pm
Subject: [WSJTX] Version 2.5 trouble #Windows10 #transmit #Kenwood

Hello everyone,

I have recently upgraded from 2.2 to 2.5 and now have troubles.

All seems to look OK but I cannot connect with anyone.

I am decoding just fine, green bar about 65.

TX seems OK on my 590-SG using USB interface, ALC is 1 bar on TX.

time.is says I am exact.

auto seq is checked.

When I double click on a cq the TX comes on and I am calling that
station and their call is now in the TX windows.

When someone answers my cq their call does not show up in the TX1 window
and the TX6 window is still checked.

again auto seq is checked.


Thoughts please,

Dave KC3AM











locked Re: IC 705 CRASHES WSJT-X WHEN TX #band #AudioIssues #Icom

Michael Black
 

And is your ground rod bonded to the house ground too?

Mike W9MDB




On Sunday, November 28, 2021, 03:19:47 PM CST, Gary trock <gtrockmd@...> wrote:


Mark, I’m new to WSJTx but for ham radio in general, I have 6 copper ground rods, 6 feet long bonded with #4 gauge wire and many would consider that inadequate grounding. One rod not enough.
Gary N8GT
> On Nov 28, 2021, at 1:16 PM, Gary trock <gtrockmd@...> wrote:
>
> Question. I’m using an old Kenwood TS 850s, and thinking of getting a second radio. I am considering an ICOM 7300, but noticed how cheap IC 718’s are at the present. Any comments good or bad using the 718 for WSJTx?
> Gary N8GT
>> On Nov 28, 2021, at 1:13 PM, Mark Gottlieb <kk2l@...> wrote:
>>
>> I just got back to the group.  My shack is grounded to a copper rod buried in my garden.  All radios, amps, tuners etc are wired to the same copper rod.
>>
>>
>> 73
>> Mark
>> KK2L
>>
>>
>
>
>




locked Re: IC 705 CRASHES WSJT-X WHEN TX #band #AudioIssues #Icom

Michael Black
 

It depends on how susceptible the USB cable is to RFI.

Mike W9MDB




On Sunday, November 28, 2021, 03:25:38 PM CST, Mark Gottlieb <kk2l@...> wrote:


I should have come back to the group sooner.  I didn't get an e-mail that my original post was answered.  Anyway...bingo!  Yes, when I reduce power, (down to 45 watts) even on the upper bands, the radio is performing nominally with WSJT-x with my IC 7100..  But... and this is one I can't understand...I was only using 10 watts with the IC 705 and it was still failing. 


Mark 
KK2L




locked Re: IC 705 CRASHES WSJT-X WHEN TX #band #AudioIssues #Icom

Mark Gottlieb
 

I should have come back to the group sooner.  I didn't get an e-mail that my original post was answered.  Anyway...bingo!  Yes, when I reduce power, (down to 45 watts) even on the upper bands, the radio is performing nominally with WSJT-x with my IC 7100..  But... and this is one I can't understand...I was only using 10 watts with the IC 705 and it was still failing. 

Mark 
KK2L


locked Re: IC 705 CRASHES WSJT-X WHEN TX #band #AudioIssues #Icom

Gary trock
 

Mark, I’m new to WSJTx but for ham radio in general, I have 6 copper ground rods, 6 feet long bonded with #4 gauge wire and many would consider that inadequate grounding. One rod not enough.
Gary N8GT

On Nov 28, 2021, at 1:16 PM, Gary trock <gtrockmd@...> wrote:

Question. I’m using an old Kenwood TS 850s, and thinking of getting a second radio. I am considering an ICOM 7300, but noticed how cheap IC 718’s are at the present. Any comments good or bad using the 718 for WSJTx?
Gary N8GT
On Nov 28, 2021, at 1:13 PM, Mark Gottlieb <kk2l@...> wrote:

I just got back to the group. My shack is grounded to a copper rod buried in my garden. All radios, amps, tuners etc are wired to the same copper rod.


73
Mark
KK2L



locked Re: IC 705 CRASHES WSJT-X WHEN TX #band #AudioIssues #Icom

Gary trock
 

Question. I’m using an old Kenwood TS 850s, and thinking of getting a second radio. I am considering an ICOM 7300, but noticed how cheap IC 718’s are at the present. Any comments good or bad using the 718 for WSJTx?
Gary N8GT

On Nov 28, 2021, at 1:13 PM, Mark Gottlieb <kk2l@...> wrote:

I just got back to the group. My shack is grounded to a copper rod buried in my garden. All radios, amps, tuners etc are wired to the same copper rod.


73
Mark
KK2L


locked Re: IC 705 CRASHES WSJT-X WHEN TX #band #AudioIssues #Icom

Mark Gottlieb
 

One more thing...just to be clear, I am experiencing this issue on my portable CHAMELEON MPAS 2.0 which only has a radial coming from the antenna and my universally grounded (copper rod) antenna in my backyard.  However, the problem is only happening on the upper bands (>18Mhz).  The lower bands are not seeing this issue with WSJT-x.

73

Mark
KK2L


locked Re: IC 705 CRASHES WSJT-X WHEN TX #band #AudioIssues #Icom

William Smith
 

Does the problem go away if you reduce the output power to near zero and/or transmit into a dummy load? If so, it's almost certainly RFI.

73, Willie N1JBJ

On Nov 28, 2021, at 4:10 PM, Mark Gottlieb <kk2l@...> wrote:

Good Afternoon All,

I am having this same problem but only from 18mhz on up. On 14mhz down, the rig (IC7100) interfaces normally and well with WSJT-x and FLRIG. Icom radios do have a one USB cable, as we all know, for CAT and AUDIO. Is my issue attributable to the same reasons as the failure others are experiencing? I have tried changing antennas, taking the tuner out of the mix, changing USB cables but the problem persists. Any help would be most appreciated.


73
Mark
KK2L


locked Re: IC 705 CRASHES WSJT-X WHEN TX #band #AudioIssues #Icom

Mark Gottlieb
 

I just got back to the group.  My shack is grounded to a copper rod buried in my garden.  All radios, amps, tuners etc are wired to the same copper rod.


73
Mark
KK2L


locked Re: IC 705 CRASHES WSJT-X WHEN TX #band #AudioIssues #Icom

Mark Gottlieb
 

Good Afternoon All,

I am having this same problem but only from 18mhz on up.  On 14mhz down, the rig (IC7100) interfaces normally and well with WSJT-x and FLRIG.  Icom radios do have a one USB cable, as we all know, for CAT and AUDIO.  Is my issue attributable to the same reasons as the failure others are experiencing?  I have tried changing antennas, taking the tuner out of the mix, changing USB cables but the problem persists.  Any help would be most appreciated.


73
Mark
KK2L


locked Help needed for MAP65 network protocol #map65

yt7pwr
 

Hi to all.
I developing SDR software for LimeSDR-USB (2ch RX 0.1-3.8GHz) and I'm stuck with MAP65 network protocol. So far I managed to form UDP
packets and send them to MAP65, they are displayed but inversed (in the center of spectrum is +/-48KHz and at the both edges is 0Hz). MAP65 in lower
left corner is displaying message Receiving F2 or Receiving F1 (green all the time without any red NILL messages).
When I try to send one RF channel via soundcard (using VAC) it is working fine, decoding on 2m and 70cm Jt65 and Q65 modes but only one polarization.
Where can I find documentation for struct Linrad (from file soundin.cpp, line 339)? Using Wireshark I'm monitoring UDP packets and they look like packets
from Linrad but not 100% sure about first 24 bytes (packet header). Change passband_direction in header has no effect. Maybe I need to change settings
inside MAP65 program?

Goran, yt7pwr


locked Re: #Kenwood #WSJTX_config #Windows10 #FTDI #ftdi #WSJTX_config #Windows10 #ftdi #Kenwood

Michael Black
 

What does "just not perfect" mean?
 
Mike W9MDB
 
 
 
 

On Sunday, November 28, 2021, 02:52:13 AM CST, <mark.salvador@...> wrote:
 
 
Yes sir, I actually was in touch with the tech from xggcomms which is great, its just that the errors are on the software and my rig is old TS-450s and is tagged as obsolete with Kenwood.  Have to survive this self inflicted pain i'm getting hahaha.

But was able to make it work in 2 days just not perfect yet.




73!




locked Re: OMNIRIG 1.9 ~ IC-705 Issue #Cat_RigControl

Michael Black
 

What order do you start your software?
 
Do you have Log4OM starting WSJTX?  
Try starting WSJTX before Log4OM.
 
Mike W9MDB
 
 
 

On Sunday, November 28, 2021, 03:45:57 AM CST, Dave H <xwebsubs@...> wrote:
 
 

Hi Bill & Mike,

I have re-visited all radio / software settings, and changed speed to 19,200 & poll: 100ms , No Change
I also tried latest version of omnirig, 1.20 , No Change

Going to try installing everything on another PC, see what happens.

I may try a question on LOG4OM Forum
I only observed the issue since trying LOG4OM, maybe somebody else had an issue..??



73 Dave G8LIY

 




locked Re: wsjtx.log & wsjtx_log.adi #adiFiles

Hamish G0GLG
 

Hi,

Thank you all for the replies and I must make an apology Bill I was incorrect in my statement that it slowed down the programme as I have no evidence of this.
As for the uploading of the adif file due to its size it does slow down the way way in which I carry out this task, which is by using the online logging uploader. As suggested here by some others I will just create a dummy adif file and copy and paste the new files for upload into that.

Thanks again for all replies.

73 all Hamish 


locked Re: OMNIRIG 1.9 ~ IC-705 Issue #Cat_RigControl

Dave H
 

Hi Bill & Mike,

I have re-visited all radio / software settings, and changed speed to 19,200 & poll: 100ms , No Change
I also tried latest version of omnirig, 1.20 , No Change

Going to try installing everything on another PC, see what happens.

I may try a question on LOG4OM Forum
I only observed the issue since trying LOG4OM, maybe somebody else had an issue..??

73 Dave G8LIY


locked WSJT-X & JTAlert Interface #Windows10 #WSJTX_config

Larry Scantlan
 

I have downloaded the latest versions for both WSJT-X (v.2.5.2) and JTAlert (v.2.50.8) and installation completed as it should .  WSJT-X is operating fine as I have completed several QSOs just fine.  I have JTAlert configured to start WSJT-X which it does without issue.  What is NOT happening is none of the JTAlert screens are populating decoded callsigns or any other data from decodes showing in the WSJT-X screen.  It does not populate the band distribution table showing FT8, FT4, JT65, etc either.  I have gone into the JTAlert View dropdown and clicked on Callsigns Window (F3) but not change.  I uninstalled both programs and re-installed them but experienced the same result.  My operating system is Windows OS 10 Pro.  Before the change to JTAlert's layout when it was just one screen showing decodes, it worked well.  Anyone have any suggestions?  Thanks, de Larry, NA4DX


locked Re: #Kenwood #WSJTX_config #Windows10 #FTDI #ftdi #WSJTX_config #Windows10 #ftdi #Kenwood

mark.salvador@...
 

Yes sir, I actually was in touch with the tech from xggcomms which is great, its just that the errors are on the software and my rig is old TS-450s and is tagged as obsolete with Kenwood.  Have to survive this self inflicted pain i'm getting hahaha.

But was able to make it work in 2 days just not perfect yet.



73!


locked Re: Codecs and names: #WSJTX_config #windows11

Michael Black
 

There are numerous places where these names exist in the registry.

Just search for the name in regedit and eventually you'll find the one that works.
On my system it was these two keys


HKEY_CURRENT_USER\Software\Microsoft\ActiveMovie\devenum 64-bit\{33D9A762-90C8-11D0-BD43-00A0C911CE86}\wave:{5A7A3363-0608-4A4F-96BB-E903D6EFF165}
HKEY_CURRENT_USER\Software\Microsoft\ActiveMovie\devenum 64-bit\{E0F158E1-CB04-11D0-BD4E-00A0C911CE86}\wave:{2B317D26-CACB-4A20-9A63-78337ECB5000}

Mike W9MDB

8081 - 8100 of 38211