main@WSJTX.groups.io

Home Messages Hashtags Subgroups

Between

and

Re: WSJT-X 2.3.0 and FLrig #Cat_RigControl Joe Dz #29006 Dave, Like the other station, all versions of WSJT-X work directly with my TS-590SG for CAT control, both on Windows 10 and Ubuntu LINUX using the USB cable. I do not use flrig. Joe, K1YOW toggle quoted messageShow quoted text From: main@WSJTX.groups.io [mailto:main@WSJTX.groups.io] On Behalf Of Dave Garber Sent: Friday, September 24, 2021 10:42 PM To: WSJT-x group Subject: Re: [WSJTX] WSJT-X 2.3.0 and FLrig #Cat_RigControl are you using flrig for cat control in the older version of wsjt?? why not go direct to radio from wsjt.... just wondering Dave Garber VE3WEJ / VE3IE On Fri, Sep 24, 2021 at 5:46 PM Kun N7DMR <sa4591@...> wrote: I still have problems with FLRig with this json files on the log directory.
More All Messages By This Member
Re: Audio Frequency choice. #QSO_practices Bill Somerville #29005 On 24/09/2021 23:12, mbigos@sonic.net wrote: Hi - I have been using FT8 for 4 months on 40 & 20 meters and notice that signals bunch between 1 kHz and 2 to 2.5 kHz. Can someone explain to me (or point me at some good write-ups) as to why this happens? Is there some magic going on that I am missing, or is it just herd instinct? I generally try to use 800-950 Hz, and get reasonable results with a QRP rig and compromise antenna. Thanks in advance, 73. Marty KN6OKN Hi Marty, one reason may be that users who do not have CAT control of their rigs are following our advice to use Tx audio offsets above 1500 Hz. This ensures that any unwanted audio harmonics are greatly attenuated by the rig's Tx IF filter. Of course they can elect to tune their VFO dial down 1 or 1.5 kHz if they wish to get to those lower frequencies. 73 Bill G4WJS.
More All Messages By This Member
Re: Audio Frequency choice. #QSO_practices mike #29004 Simples, you are transmitting an audio tome on an SSB transmitter, the bandwidth of the SSB transmitter is roughly 300Hz to 3Khz, anything outside that will not be transmitted or severely attenuated. Your receiver has an audio response to fit with the SSB TX response.. OK ? toggle quoted messageShow quoted text On 24 Sep 2021 at 15:12, mbigos@sonic.net wrote: Subject: [WSJTX] Audio Frequency choice. #QSO_practices To: main@WSJTX.groups.io From: mbigos@sonic.net Date sent: Fri, 24 Sep 2021 15:12:10 -0700 Send reply to: main@WSJTX.groups.io Hi - I have been using FT8 for 4 months on 40 & 20 meters and notice that signals bunch between 1 kHz and 2 to 2.5 kHz. Can someone explain to me (or point me at some good write-ups) as to why this happens? Is there some magic going on that I am missing, or is it just herd instinct? I generally try to use 800-950 Hz, and get reasonable results with a QRP rig and compromise antenna. Thanks in advance, 73. Marty KN6OKN
More All Messages By This Member
Audio Frequency choice. #QSO_practices Marty Bigos #29003 Hi - I have been using FT8 for 4 months on 40 & 20 meters and notice that signals bunch between 1 kHz and 2 to 2.5 kHz. Can someone explain to me (or point me at some good write-ups) as to why this happens? Is there some magic going on that I am missing, or is it just herd instinct? I generally try to use 800-950 Hz, and get reasonable results with a QRP rig and compromise antenna. Thanks in advance, 73. Marty KN6OKN
More All Messages By This Member
Re: TS-590SG control #Cat_RigControl #Kenwood Dave #29002 Dave, All I use with my 590SG is the USB cable. I start N3FJP first then start WSJT and they talk, control the 590, do a QRZ lookup & log each contact. No DB9 cable used at all and no ARCP software used. Dave KC3AM toggle quoted messageShow quoted text On 09/23/2021 07:40, Dave Garber wrote: why do you need arcp software running, while doing digital?? I use the db9 for cat, and the usb port for wsjtx. i do not run the arcp software unless I do cw ( rarely) or need some changes in the radio ( rarely) Dave Garber VE3WEJ / VE3IE On Wed, Sep 22, 2021 at 3:24 PM KA5VZG <ka5vzg@...> wrote: I have the Kenwood virtual com port , SDRuno, OmniRig, and ARCP-590G loaded. I can get two to work at the same time. I can have SDRuno running on one monitor and have fldigi controlling the rig on the other. If SDRuno is controlling the rig, fldigi or WSJT-X wont. I am assuming that the virtual com port will only permit two things to share the port at a time. When running WSJT-X, sometimes when I click on the dropdown to change frequencies I get an orange display where the frequency normally is displayed (see picture) at this point, sometimes clicking on the frequency dropdown will open it up again, but it usually will not permit changing the frequency on the rig. Before this it functioned OK, i.e. can activate the xmtr with the TUNE, and adjust power with the slider. Anyone else seen this? Fix? -- 73, Dave KC3AM Hams should be seen as well as heard
More All Messages By This Member
Re: WSJT-X 2.3.0 and FLrig #Cat_RigControl Dave Garber #29001 are you using flrig for cat control in the older version of wsjt?? why not go direct to radio from wsjt.... just wondering Dave Garber VE3WEJ / VE3IE toggle quoted messageShow quoted text On Fri, Sep 24, 2021 at 5:46 PM Kun N7DMR <sa4591@...> wrote: I still have problems with FLRig with this json files on the log directory.
More All Messages By This Member
Re: WSJT-X 2.3.0 and FLrig #Cat_RigControl Kun N7DMR #29000 I still have problems with FLRig with this json files on the log directory.
More All Messages By This Member
Re: TS-590SG control #Cat_RigControl #Kenwood Larry Crouch #28999 I too run just wsjt on Linux to control CAT through USB on my TS590SG. I do not use a separate cable for anything, everything is through USB and I only run wsjt, not any other software. Larry Crouch larry@larkat.com WA5PCR EM12 toggle quoted messageShow quoted text On 9/24/21 8:49 AM, Joe Dz wrote: There is no need to run arcp software while running WSJT. I operate WSJT-X modes just fine running WSJT-X software stand-alone just using a USB cable to connect my TS-590SG to a Windows 10 or LINUX computer. Joe, K1YOW ------------------------------------------------------------------------ From:main@WSJTX.groups.io [mailto:main@WSJTX.groups.io] On Behalf Of Dave Garber Sent: Friday, September 24, 2021 7:04 AM To: WSJT-x group Subject: Re: [WSJTX] TS-590SG control #Cat_RigControl #Kenwood regardless of db9, still does not explain my original question why the need to run arcp software while running wsjt Dave Garber VE3WEJ / VE3IE On Thu, Sep 23, 2021 at 10:45 AM Gilbert Baron <w0mn00@gmail.com <mailto:w0mn00@gmail.com>> wrote: Both CAT and WSJTX can be done through the USB port. The DB9 is not needed. I have a TS590-SG and do not use DB9 at all. Outlook Laptop Gil W0MN Hierro candente, batir de repente 44.08226N 92.51265W EN34rb From: main@WSJTX.groups.io <mailto:main@WSJTX.groups.io> <main@WSJTX.groups.io <mailto:main@WSJTX.groups.io>> On Behalf Of Dave Garber Sent: Thursday, September 23, 2021 06:40 To: WSJT-x group <main@wsjtx.groups.io <mailto:main@wsjtx.groups.io>> Subject: Re: [WSJTX] TS-590SG control #Cat_RigControl #Kenwood why do you need arcp software running, while doing digital?? I use the db9 for cat, and the usb port for wsjtx. i do not run the arcp software unless I do cw ( rarely) or need some changes in the radio ( rarely) Dave Garber VE3WEJ / VE3IE On Wed, Sep 22, 2021 at 3:24 PM KA5VZG <ka5vzg@arrl.net <mailto:ka5vzg@arrl.net>> wrote: I have the Kenwood virtual com port , SDRuno, OmniRig, and ARCP-590G loaded. I can get two to work at the same time. I can have SDRuno running on one monitor and have fldigi controlling the rig on the other. If SDRuno is controlling the rig, fldigi or WSJT-X wont. I am assuming that the virtual com port will only permit two things to share the port at a time. When running WSJT-X, sometimes when I click on the dropdown to change frequencies I get an orange display where the frequency normally is displayed (see picture) at this point, sometimes clicking on the frequency dropdown will open it up again, but it usually will not permit changing the frequency on the rig. Before this it functioned OK, i.e. can activate the xmtr with the TUNE, and adjust power with the slider. Anyone else seen this? Fix? -- W0MN EN34rb 44.08226 N 92.51265 W Hierro candente, batir de repente HP Laptop OpenPGP_0x1EFEEE9A30FE92B7.asc OpenPGP_signature
More All Messages By This Member
FT8 TX5 73 not sent after RRR #Windows10 #QSO_practices NR4U Bob AFMARS #28998 v2.5.0-rc6 FT8 Hold-Tx Auto-Seq Windows-10-Pro twice I've noted that after RRR is sent that wsjtx ceases to xmit and TX5 is not issued. fwiw, "disable TX after 73" remains unchecked. I am on 144.174 FT8 -- -- Bob KD7YZ in NE Kentucky
More All Messages By This Member
Re: TS-590SG control #Cat_RigControl #Kenwood Joe Dz #28997 There is no need to run arcp software while running WSJT. I operate WSJT-X modes just fine running WSJT-X software stand-alone just using a USB cable to connect my TS-590SG to a Windows 10 or LINUX computer. Joe, K1YOW toggle quoted messageShow quoted text From: main@WSJTX.groups.io [mailto:main@WSJTX.groups.io] On Behalf Of Dave Garber Sent: Friday, September 24, 2021 7:04 AM To: WSJT-x group Subject: Re: [WSJTX] TS-590SG control #Cat_RigControl #Kenwood regardless of db9, still does not explain my original question why the need to run arcp software while running wsjt Dave Garber VE3WEJ / VE3IE On Thu, Sep 23, 2021 at 10:45 AM Gilbert Baron <w0mn00@...> wrote: Both CAT and WSJTX can be done through the USB port. The DB9 is not needed. I have a TS590-SG and do not use DB9 at all. Outlook Laptop Gil W0MN Hierro candente, batir de repente 44.08226N 92.51265W EN34rb From: main@WSJTX.groups.io <main@WSJTX.groups.io> On Behalf Of Dave Garber Sent: Thursday, September 23, 2021 06:40 To: WSJT-x group <main@wsjtx.groups.io> Subject: Re: [WSJTX] TS-590SG control #Cat_RigControl #Kenwood why do you need arcp software running, while doing digital?? I use the db9 for cat, and the usb port for wsjtx. i do not run the arcp software unless I do cw ( rarely) or need some changes in the radio ( rarely) Dave Garber VE3WEJ / VE3IE On Wed, Sep 22, 2021 at 3:24 PM KA5VZG <ka5vzg@...> wrote: I have the Kenwood virtual com port , SDRuno, OmniRig, and ARCP-590G loaded. I can get two to work at the same time. I can have SDRuno running on one monitor and have fldigi controlling the rig on the other. If SDRuno is controlling the rig, fldigi or WSJT-X wont. I am assuming that the virtual com port will only permit two things to share the port at a time. When running WSJT-X, sometimes when I click on the dropdown to change frequencies I get an orange display where the frequency normally is displayed (see picture) at this point, sometimes clicking on the frequency dropdown will open it up again, but it usually will not permit changing the frequency on the rig. Before this it functioned OK, i.e. can activate the xmtr with the TUNE, and adjust power with the slider. Anyone else seen this? Fix? -- W0MN EN34rb 44.08226 N 92.51265 W Hierro candente, batir de repente HP Laptop
More All Messages By This Member
Re: TS-590SG control #Cat_RigControl #Kenwood Dave Garber #28996 regardless of db9, still does not explain my original question why the need to run arcp software while running wsjt Dave Garber VE3WEJ / VE3IE toggle quoted messageShow quoted text On Thu, Sep 23, 2021 at 10:45 AM Gilbert Baron <w0mn00@...> wrote: Both CAT and WSJTX can be done through the USB port. The DB9 is not needed. I have a TS590-SG and do not use DB9 at all. Outlook Laptop Gil W0MN Hierro candente, batir de repente 44.08226N 92.51265W EN34rb From: main@WSJTX.groups.io <main@WSJTX.groups.io> On Behalf Of Dave Garber Sent: Thursday, September 23, 2021 06:40 To: WSJT-x group <main@wsjtx.groups.io> Subject: Re: [WSJTX] TS-590SG control #Cat_RigControl #Kenwood why do you need arcp software running, while doing digital?? I use the db9 for cat, and the usb port for wsjtx. i do not run the arcp software unless I do cw ( rarely) or need some changes in the radio ( rarely) Dave Garber VE3WEJ / VE3IE On Wed, Sep 22, 2021 at 3:24 PM KA5VZG <ka5vzg@...> wrote: I have the Kenwood virtual com port , SDRuno, OmniRig, and ARCP-590G loaded. I can get two to work at the same time. I can have SDRuno running on one monitor and have fldigi controlling the rig on the other. If SDRuno is controlling the rig, fldigi or WSJT-X wont. I am assuming that the virtual com port will only permit two things to share the port at a time. When running WSJT-X, sometimes when I click on the dropdown to change frequencies I get an orange display where the frequency normally is displayed (see picture) at this point, sometimes clicking on the frequency dropdown will open it up again, but it usually will not permit changing the frequency on the rig. Before this it functioned OK, i.e. can activate the xmtr with the TUNE, and adjust power with the slider. Anyone else seen this? Fix? -- W0MN EN34rb 44.08226 N 92.51265 W Hierro candente, batir de repente HP Laptop
More All Messages By This Member
Re: A Pocket Sized FT Transceiver #decode #FT8 #transmit #Waterfall oz1bxm_lars_petersen #28995 Hi Charles, W5BAA What a great project! I've started to collect components in order to build the "Pocket FT8". I'll announce my results in this group. 73 OZ1BXM Lars Petersen
More All Messages By This Member
Re: #install #Yaesu #WindowsXP #install #Yaesu #WindowsXP Carlos #28994 Hi Tom, My first Hamradio PC runs also only Win XP prof Sp3. And I have WSJT-x 2.1.0 running perfect. For me no need to have a later version ! I use WSJT-x only for KW. My second Hamradio PC is a raspberry with buster OS. Here I run the latest WSJT-X 2.5.0. This works also OK, in my case only for SAT and MS. Hope I could give you a helping hand, 73, Karl OE3JAG Am 23.09.2021 um 00:11 schrieb Tom Ryan via groups.io: toggle quoted messageShow quoted text I'm a new user and I need help! I have an FT-897 that is my dedicated digital station. It is running on an older Dell Optiplex desktop. The OS is XP Prefessional with service pack 3. It is not hooked up to my wireless home network due to security issues with the XP OS. I work various digital modes on it through a SignaLink USB. I want to install WSJT-X on this system. I tried downloading it onto a flash drive with my Windows 10 machine but all of the needed components won't load onto the flash drive. any suggestions?? 73 Tom KD6TR
More All Messages By This Member
Re: K55Z #FT8 n1ig.anthony@... #28993 Edited I think it may have been ks5z. the grid square shown on psk reporter for k55z and ks5z on qrz, are both the same. try emailing him. Anthony - n1IG
More All Messages By This Member
Re: TS-590SG control #Cat_RigControl #Kenwood Gilbert Baron #28992 Both CAT and WSJTX can be done through the USB port. The DB9 is not needed. I have a TS590-SG and do not use DB9 at all. Outlook Laptop Gil W0MN Hierro candente, batir de repente 44.08226N 92.51265W EN34rb toggle quoted messageShow quoted text From: main@WSJTX.groups.io <main@WSJTX.groups.io> On Behalf Of Dave Garber Sent: Thursday, September 23, 2021 06:40 To: WSJT-x group <main@wsjtx.groups.io> Subject: Re: [WSJTX] TS-590SG control #Cat_RigControl #Kenwood why do you need arcp software running, while doing digital?? I use the db9 for cat, and the usb port for wsjtx. i do not run the arcp software unless I do cw ( rarely) or need some changes in the radio ( rarely) Dave Garber VE3WEJ / VE3IE On Wed, Sep 22, 2021 at 3:24 PM KA5VZG <ka5vzg@...> wrote: I have the Kenwood virtual com port , SDRuno, OmniRig, and ARCP-590G loaded. I can get two to work at the same time. I can have SDRuno running on one monitor and have fldigi controlling the rig on the other. If SDRuno is controlling the rig, fldigi or WSJT-X wont. I am assuming that the virtual com port will only permit two things to share the port at a time. When running WSJT-X, sometimes when I click on the dropdown to change frequencies I get an orange display where the frequency normally is displayed (see picture) at this point, sometimes clicking on the frequency dropdown will open it up again, but it usually will not permit changing the frequency on the rig. Before this it functioned OK, i.e. can activate the xmtr with the TUNE, and adjust power with the slider. Anyone else seen this? Fix? -- W0MN EN34rb 44.08226 N 92.51265 W Hierro candente, batir de repente HP Laptop
More All Messages By This Member
Re: TS-590SG control #Cat_RigControl #Kenwood Dave Garber #28991 why do you need arcp software running, while doing digital?? I use the db9 for cat, and the usb port for wsjtx. i do not run the arcp software unless I do cw ( rarely) or need some changes in the radio ( rarely) Dave Garber VE3WEJ / VE3IE toggle quoted messageShow quoted text On Wed, Sep 22, 2021 at 3:24 PM KA5VZG <ka5vzg@...> wrote: I have the Kenwood virtual com port , SDRuno, OmniRig, and ARCP-590G loaded. I can get two to work at the same time. I can have SDRuno running on one monitor and have fldigi controlling the rig on the other. If SDRuno is controlling the rig, fldigi or WSJT-X wont. I am assuming that the virtual com port will only permit two things to share the port at a time. When running WSJT-X, sometimes when I click on the dropdown to change frequencies I get an orange display where the frequency normally is displayed (see picture) at this point, sometimes clicking on the frequency dropdown will open it up again, but it usually will not permit changing the frequency on the rig. Before this it functioned OK, i.e. can activate the xmtr with the TUNE, and adjust power with the slider. Anyone else seen this? Fix?
More All Messages By This Member
Re: #install #Yaesu #WindowsXP #install #Yaesu #WindowsXP Gilbert Baron #28990 I would not be at all surprised if needed components are not available in that ancient OS. I would load W10 or at least W7 (assuming it can be done) on it and Away you go. If not then perhaps make it into a Linux system. Outlook Laptop Gil W0MN Hierro candente, batir de repente 44.08226N 92.51265W EN34rb toggle quoted messageShow quoted text From: main@WSJTX.groups.io <main@WSJTX.groups.io> On Behalf Of Tom Ryan via groups.io Sent: Wednesday, September 22, 2021 17:12 To: main@WSJTX.groups.io Subject: [WSJTX] #install #Yaesu #WindowsXP I'm a new user and I need help! I have an FT-897 that is my dedicated digital station. It is running on an older Dell Optiplex desktop. The OS is XP Prefessional with service pack 3. It is not hooked up to my wireless home network due to security issues with the XP OS. I work various digital modes on it through a SignaLink USB. I want to install WSJT-X on this system. I tried downloading it onto a flash drive with my Windows 10 machine but all of the needed components won't load onto the flash drive. any suggestions?? 73 Tom KD6TR -- W0MN EN34rb 44.08226 N 92.51265 W Hierro candente, batir de repente HP Laptop
More All Messages By This Member
Re: #install #Yaesu #WindowsXP #install #Yaesu #WindowsXP Alan G4ZFQ #28989 It is running on an older Dell Optiplex desktop. The OS is XP Prefessional with service pack 3. Tom, Older versions here https://sourceforge.net/projects/wsjt/files/ I guess you'll have to check, maybe some modes have changed but older like WSPR will still work, perhaps not quite so well. 73 Alan G4ZFQ
More All Messages By This Member
Re: #install #Yaesu #WindowsXP #install #Yaesu #WindowsXP William Smith #28988 V2.2.0 from June 2020 was the first release to drop support for XP. Try Win10 or macOS or Linux. 73, Willie N1JBJ toggle quoted messageShow quoted text On Sep 23, 2021, at 4:44 AM, Tom Ryan via groups.io <kd6tr=yahoo.com@groups.io> wrote: I'm a new user and I need help! I have an FT-897 that is my dedicated digital station. It is running on an older Dell Optiplex desktop. The OS is XP Prefessional with service pack 3. It is not hooked up to my wireless home network due to security issues with the XP OS. I work various digital modes on it through a SignaLink USB. I want to install WSJT-X on this system. I tried downloading it onto a flash drive with my Windows 10 machine but all of the needed components won't load onto the flash drive. any suggestions?? 73 Tom KD6TR
More All Messages By This Member
Re: #install #Yaesu #WindowsXP #install #Yaesu #WindowsXP Bill Somerville #28987 On 22/09/2021 23:11, Tom Ryan via groups.io wrote: I'm a new user and I need help! I have an FT-897 that is my dedicated digital station. It is running on an older Dell Optiplex desktop. The OS is XP Prefessional with service pack 3. It is not hooked up to my wireless home network due to security issues with the XP OS. I work various digital modes on it through a SignaLink USB. I want to install WSJT-X on this system. I tried downloading it onto a flash drive with my Windows 10 machine but all of the needed components won't load onto the flash drive. any suggestions?? 73 Tom KD6TR Hi Tom, as noted here: https://physics.princeton.edu/pulsar/k1jt/wsjtx.html and here: https://sourceforge.net/projects/wsjt/files/wsjtx-2.4.0/ WSJT-X no longer supports Windows XP. 73 Bill G4WJS.
More All Messages By This Member

5621 - 5640 of 34363

Home Hashtags Subgroups About Features Pricing Updates Terms Help Twitter