Date   

locked Re: Is there a standard frequency used for F&H #FoxAndHound #FT8

neil_zampella
 

Not really, although there are some that are frequently used, but to eliminate QRM, most DXPeditions will list on a webpage what frequencies they will be using.

Neil, KN3ILZ

On 8/26/2021 9:06 AM, Norman Heyen wrote:
I've looked and not found an answer. Is there a common frequency that DX expeditions use for Fox & Hound operations? 
73, 
Norman 
KC9NVN




locked Re: Auto Seq Changes DX Call ? #logging

 

It looks like the TNX 2BND 73 message has been coded into a standard <CALL> <CALL> 73 format. WSJT-X is not going to know that it’s not a real call.

 

I don’t know if there’s a way for WSJT-X to be told not to.  It’s only 11 characters so there could be a way for the sender add one or two characters – say “TNX 2BND 73SK”

 

73 Phil GM3ZZA

 

Sent from Mail for Windows

 

From: Bob KM4RL
Sent: 26 August 2021 14:42
To: main@WSJTX.groups.io
Subject: Re: [WSJTX] Auto Seq Changes DX Call ? #logging

 

Here is a screenshot.

Thanks,
Bob KM4RL

 


--
73 Phil GM3ZZA


locked Is there a standard frequency used for F&H #FoxAndHound #FT8

Norman Heyen
 

I've looked and not found an answer. Is there a common frequency that DX expeditions use for Fox & Hound operations? 
73, 
Norman 
KC9NVN


locked Re: After upgrade to WSJT-X 2.4.0, an IC-7600 no longer changes bands on SPE Expert 1K-FA power amplifier #Cat_RigControl

Don Melcher
 


locked Re: Auto Seq Changes DX Call ? #logging

Bob KM4RL
 

Here is a screenshot.

Thanks,
Bob KM4RL


locked Re: #txaudio #linux WSJT-X No TX audio issue #txaudio #linux

KM4OVZ
 
Edited

do not use the system default audio devices for transmitter Tx audio
Well I did try selecting the actual device as well but the effect is the same. Default output works fine. It's gotta be an bug on WSJT-X's end because it works fine on the windows version.


locked Re: #txaudio #linux WSJT-X No TX audio issue #txaudio #linux

Bill Somerville
 

On 26/08/2021 13:38, KM4OVZ wrote:
The rig I'm trying to use is an icom 7300, as well as a Yaesu FT-100. Both have fine cat control on Linux, with the active frequency showing in wsjtx. TX works fine but there's no audio output. The way audio is sent to the radio is by an external audio port on the computer. Alternatively a USB soundcard can be used for the same result of sending audio out.

WSJTX has "default" set for both input and output audio. The current devices are set as default and selected in the OS. Playing audio from any other program works as expected. Audio goes in, shows on the waterfall, and decodes fine. Wsjtx just isn't putting out any sound! No sources pop up in pavucontrol when it's in transmit mode either.

Running 'padsp wsjtx' will make the first transmission have audio, but on the next cycle there's no sound again.
OM (name ??),

do not use the system default audio devices for transmitter Tx audio.

73
Bill
G4WJS.


locked Re: #txaudio #linux WSJT-X No TX audio issue #txaudio #linux

KM4OVZ
 
Edited

Does the wsjtx soundcard output descriptor match that expected and shown with aplay -l   ?

Yes it matches


locked Re: #txaudio #linux WSJT-X No TX audio issue #txaudio #linux

KM4OVZ
 

TX Power has no effect :(


locked Re: #txaudio #linux WSJT-X No TX audio issue #txaudio #linux

KM4OVZ
 

The rig I'm trying to use is an icom 7300, as well as a Yaesu FT-100. Both have fine cat control on Linux, with the active frequency showing in wsjtx. TX works fine but there's no audio output. The way audio is sent to the radio is by an external audio port on the computer. Alternatively a USB soundcard can be used for the same result of sending audio out. 

WSJTX has "default" set for both input and output audio. The current devices are set as default and selected in the OS. Playing audio from any other program works as expected. Audio goes in, shows on the waterfall, and decodes fine. Wsjtx just isn't putting out any sound! No sources pop up in pavucontrol when it's in transmit mode either. 

Running 'padsp wsjtx' will make the first transmission have audio, but on the next cycle there's no sound again. 


locked Re: #FT8 TX does not work correctly after installing WSJT-X v2.4.0 #FT8 #Cat_RigControl

WILLIAM MILLS KY4IF 2859E <lsihhc8224@...>
 

CAT is connected and appeares to be working. I can hear it controling the G90. The problem is ALL of my volume controls are completely different than what is shown in that post. I have no Idea what I am doing at this point. I miss Windows XP. I have windows 10 Pro and can not find any of the settings you mention.


locked Re: Not So New Subject I suspect - WSJT-X v2.4.0 Will not transmit #Cat_RigControl #transmit

Michael Black
 

Neither the TS2000 nor PowerSDR requires 2 stop bits.
 
I haven't found a rig yet that doesn't work using all the Default settings.  That's why I added the Default capability to WSJTX to avoid all these "what settings do I use" questions on those items.
 
Mike W9MDB
 
 
 
 

On Thursday, August 26, 2021, 12:50:51 AM CDT, Miguel, EA4BAS <ea4bas@...> wrote:
 
 

Hi Dick

 

Please on DATA BITS you must mark:

 

EIGHT, TWO and NONE

On MODE

USB

On Split Operation Fake it

 

Baud rate, I use 38400 must be the same on MENU 56 on Kenwood TS200

 

GL and 73

Miguel, EA4BAS

 

 

De: main@WSJTX.groups.io [mailto:main@WSJTX.groups.io] En nombre de Dick Bingham
Enviado el: miércoles, 25 de agosto de 2021 23:04
Para: main@WSJTX.groups.io
Asunto: Re: [WSJTX] Not So New Subject I suspect - WSJT-X v2.4.0 Will not transmit #Cat_RigControl #transmit

 

I forgot to include ===>





Dick/w7wkr





locked Re: #txaudio #linux WSJT-X No TX audio issue #txaudio #linux

Nick
 

No problems here using Ubuntu 18.04 and wsjt-x-2.4.0. But I do not use pulseaudio.

Have you tried setting the TX sound card level in alsamixer? If the level is set to 0 not sure what pulseaudio will make of it.


locked Re: Not sure if this a known problem or not #AudioIssues

Pietro Molina
 

Colin, I had the same problem after upgrading WSJT-X to 2.4 with my FT817. Unexpectedly I resolved using 38.400 as baud rate instead of 9.600 for CAT, and now I'm using 2.5 beta. I think there is some time-out problem somewhere.

Pietro I2OIM


locked Re: Yaesu FT-891 Settings Needed #signalink #raspberryPi

Kenneth Blackwell
 

Folks,

Attached is a .pdf file with 4 sources for FT-891 settings. Thank you for your input.

At this point, I still have not been able to make WSJT-X run on the Pi.....so I am concluding this posting....and giving up on the Pi.

I don't believe that the problem lies just in the FT-891 settings. I was able to get a UBUNTU Laptop running nicely using the settings in the last column  in the attached pdf. The Pi problem probably has more to do with Sound Setting in the Raspberry OS or something else that I can't figure out. I tried pavucontrol (Pulse Audio) but had problems (When transmitting the monitor would shut off, no picture).

Again, Thanks to all of you. Good luck with WSJT-X

Ken, KB4XT


locked Re: Not sure if this a known problem or not #AudioIssues

d_ziolkowski
 

Colin-
also check all your rf connecters, one may have loosened up. 

Dan KC2STA

On Thu, Aug 26, 2021 at 5:39 AM colin via groups.io <csaggers1=sky.com@groups.io> wrote:

Thank you Bill

I will try some ferrites on the usb cable unless you know of a better solution.

Thanks again

Colin

G0osk

 

Sent from Mail for Windows

 

From: Bill Somerville
Sent: 25 August 2021 22:59
To: main@WSJTX.groups.io
Subject: Re: [WSJTX] Not sure if this a known problem or not #AudioIssues

 

On 25/08/2021 22:45, colin via groups.io wrote:

> Hi All

> I have been using WSJT-X for awhile now, everything has been fine

> untill the last few days.  When i try to transmit or even just tune

> WSJT-X will shut down with following errors

> WSJT-X also loses the frequency and shows OOB out of band?

> I am using WSJT-X,LOG4OM,GRIDTRACKER

> and an ft450d with a yaesu scu-17 interface.

> I would welcome any help

> Many thanks

> Colin

> G0OSK

 

Hi Colin,

 

CAT failure and audio device failure when transmitting is almost

certainly due to RFI disrupting the USB connection between your PC and

SCU-17.

 

73

Bill

G4WJS.

 

 






--
Dan Ziolkowski KC2STA
SKCC #4290T
Ubuntu LINUX


locked Re: Not sure if this a known problem or not #AudioIssues

colin
 

Thank you Bill

I will try some ferrites on the usb cable unless you know of a better solution.

Thanks again

Colin

G0osk

 

Sent from Mail for Windows

 

From: Bill Somerville
Sent: 25 August 2021 22:59
To: main@WSJTX.groups.io
Subject: Re: [WSJTX] Not sure if this a known problem or not #AudioIssues

 

On 25/08/2021 22:45, colin via groups.io wrote:

> Hi All

> I have been using WSJT-X for awhile now, everything has been fine

> untill the last few days.  When i try to transmit or even just tune

> WSJT-X will shut down with following errors

> WSJT-X also loses the frequency and shows OOB out of band?

> I am using WSJT-X,LOG4OM,GRIDTRACKER

> and an ft450d with a yaesu scu-17 interface.

> I would welcome any help

> Many thanks

> Colin

> G0OSK

 

Hi Colin,

 

CAT failure and audio device failure when transmitting is almost

certainly due to RFI disrupting the USB connection between your PC and

SCU-17.

 

73

Bill

G4WJS.

 

 


locked Re: #txaudio #linux WSJT-X No TX audio issue #txaudio #linux

Bill Somerville
 

On 26/08/2021 02:11, KM4OVZ wrote:
Hello! I'm using the Ubuntu Linux version of WSJT-X. Audio output does not seem to work at this time. Audio input works fine, I can select an input device from Pulse Audio volume control or from inside WSJT-X and it works. Decoding FT-8 works. But output audio does nothing. If I go into TX mode or Tune mode, no output source shows up in Pulse Audio and nothing can be heard on the selected output device. I've tried different devices, different audio adapters and so on. The program simply doesn't put out audio when in TX mode. TX audio works fine when the windows build of WSJT-X is ran through Wine. Audio inputs and outputs work great. However, wine doesn't work well with USB devices and as such rig control does not function.
I've tried on many different computers all running Pop OS 21.04 which is an Ubuntu based distro. I'm using the latest stable build of WSJT-X on all of them and they all give the same results with no TX audio.
If you need any more information about our systems or setup I'll be happy to answer them!
OM (name?),

telling us which rig you are using, and how it is connected to your PC for audio and CAT control, might allow us to offer some suggestions, without that information we are unlikely to be able to help you.

73
Bill
G4WJS.


locked Re: Logger32 & WSJT-X #JT65 #JT9

Bill Somerville
 

On 26/08/2021 08:10, Panos wrote:
Looks like JT modes are not in first priority, any suggestion? 73
Panos,

WSJT-X ships with a test application called message_aggregator, try running that an see if it receives the expected information when you are operating JT65 or JT9 mode. If it does then perhaps the issue lies with  Logger32.

73
Bill
G4WJS.


locked Re: Logger32 & WSJT-X #JT65 #JT9

Panos
 

Looks like JT modes are not in first priority, any suggestion? 73

9061 - 9080 of 37058