Date   

locked Re: #Cat_RigControl PTT Port ERROR happened again #Cat_RigControl

jp3exr also ja4lzx
 

Hi Sam, Jim and Bill
 
Thanks for the advice about my question.
 
Jim thanks for the advice but your advice was different from the solution I was thinking of.
 
I run multiple WSJTXs with one PC with Win 10 64bit.
Sam told me that the shared by Hamlib so I tried to finding Hamlib in WSJTX.
But Bill told me that WSJTX GA version has already PTT sharing.
Bill yes you are right, for my FT8 operation case, I run JTDX for V-pol antenna and RIG, and I run WSJTX for H-pol antenna and RIG.
WSJTX 2.4.0 rc4 version is able to it's working well.
But WSJTX 2.4.0 GA version couldn't start and it said an that error message.
It means that PTT PORT is competing with JTDX program, right?
Is this usage a violation of the rules?
 
Q65 and JT65 mode have two WSJTX running on my PC.
Of course in this case, I haven't error message when WSJTX started.
In my case FT8, Q65 and JT65 mode have each program of WSJTX and JTDX.
So each mode programs need to fine settings of the setting.
I am lucky that I run WSJTX 2.4.0 rc4 version for now.

Thank you

Taka, JP3EXR


locked Re: #BugReport #AudioIssues #IssueReport #AudioIssues

W4ARK
 

EUREKA !! Just installed the latest GA build and the issue seems to have been resolved !!

Many Thanks to all that were instrumental in resolving this issue !!

73
Paul
W4ARK


locked Re: #BugReport #AudioIssues #IssueReport #AudioIssues

W4ARK
 

Bill,
Happy to report that the issue that has been described above has been resolved  with the latest GA distribution !!  Many Thanks to all that worked to correct this anomaly and to those that commented here to  document the symptoms. 

73
Paul
W4ARK


locked VS: [WSJTX] Rig failure #WSJTX_config

Reino Talarmo
 

Using wsjt-x version 2.4.0, ft8



Any help would be appreciated. I have spent a couple of days making changes with no result. All has been working ok for months before last Windows update.

 

WSJT-X
---------------------------
Rig failure
---------------------------
Hamlib error: Communication timed out
rig_get_freq(2088): freqMainA=0, modeMainA=, widthMainA=0
rig_get_freq(2088): freqMainB=0, modeMainB=, widthMainB=0
rig.c(2090):rig_get_freq return(-5) while getting current frequency
---------------------------

Hi Peter,
Without knowing your rig and how it is connected to your PC for CAT control and your settings at Radio tab it is impossible to guess the reason. Does the Test CAT passes or is that failure a result of that test?
73, Reino OH3mA


locked Re: #BugReport No receive after transmit - rig control disables RX on Yaesu FTDX-3000 VFO A running split #IssueReport

Mark Steele
 

Checking to see if there is an anticipated update before the clock runs out on rc4.

Thanks!


locked Re: IC-7300 rig failure #WSJTX_config

Steve marsh (M0NMA)
 

That looks like you are failing to connect via the USB cable - check that you have the right com port and baud rate. 


a bit more to work on would be appreciated as well!
--
Steve M0NMA


locked Re: Antenna not showing in PSK Reporter #general

Jim Brown
 

On 5/28/2021 1:27 PM, Dave Tucker Nu4N wrote:
I noticed today that my antenna's are not showing up in PSK reporter.
Have you entered your antennas by band on the Station Information table on the Frequencies Tab in WSJT-X settings?

73, Jim K9YC


locked Re: no mike found when starting computer #AudioIssues #FT8

neil_zampella <neilz@...>
 

Quick fix ... buy a cheap $6 or $7 USB sound dongle for the laptop.  It will have separate mic and speaker connections, and this then frees up the laptop's soundcard for normal computer sounds.

Neil, KN3ILZ

On 5/28/2021 2:50 PM, rimrocktim@... wrote:

2013 Dell Latitude E6330 laptop
Windows 10 Pro
2.7 ghz processor
8 GB ram
x64 based processor (64 bit)

This laptop has a dual audio jack that is mic/headphones and is the only way to get audio on and out of the laptop.

Rig is a Kenwood TS-830S using the phones jack for audio out and the mike jack for audio in from laptop. I’m using VOX to trigger the rig.

WSJT-X v 2.3.1

I have used the rig with a Linux machine until recently with no problems.

Problem:
At startup with rig attached, the microphone is missing when I look in WSJT-X audio settings and the headphones show connected. The program will toggle the transmitter on but there is nothing being received because of the missing audio input to the laptop. It appears the laptop can’t find the mike unless there is audio coming into it. If I connect a mike/headphone to the jack and test it using Skype’s sound test the test works fine. Then when reconnecting inputs from rig to laptop I find the mike is now connected in the audio tab and WSJT-x works fine. I can then use FT8 for hours with now problems which indicates I am not dealing with some intermittent hardware issue. I have had to do this convoluted start-up procedure since I started using this laptop with my rig. Any suggestions as to a fix?




locked Re: no mike found when starting computer #AudioIssues #FT8

Joe Subich, W4TV
 

Most headphone/mic inputs are designed for electret mics and
look for a 1 mA current draw of the electret mic to turn on.

Try connecting a 2.2 K to 3.3 K resistor across the mic input
of the computer (in parallel with the audio coming from the
rig headphone jack). Typically one would have a 2.7K resistor
across the mic input, a 1uF to 5 uF cap in series with the audio
and a 10:1 voltage divider (27K resistor - can be 5K to 50K as
needed) to prevent over driving the computer mic input between
the cap and headphone jack.

If you can get into the sound card settings, you *might* be able
to *disable* "jack switching" in order to leave the mic input
available full time.

73,

... Joe, W4TV

On 2021-05-28 3:50 PM, rimrocktim@... wrote:
2013 Dell Latitude E6330 laptop
Windows 10 Pro
2.7 ghz processor
8 GB ram
x64 based processor (64 bit)
This laptop has a dual audio jack that is mic/headphones and is the only way to get audio on and out of the laptop.
Rig is a Kenwood TS-830S using the phones jack for audio out and the mike jack for audio in from laptop. I’m using VOX to trigger the rig.
WSJT-X v 2.3.1
I have used the rig with a Linux machine until recently with no problems.
Problem:
At startup with rig attached, the microphone is missing when I look in WSJT-X audio settings and the headphones show connected. The program will toggle the transmitter on but there is nothing being received because of the missing audio input to the laptop. It appears the laptop can’t find the mike unless there is audio coming into it. If I connect a mike/headphone to the jack and test it using Skype’s sound test the test works fine. Then when reconnecting inputs from rig to laptop I find the mike is now connected in the audio tab and WSJT-x works fine. I can then use FT8 for hours with now problems which indicates I am not dealing with some intermittent hardware issue. I have had to do this convoluted start-up procedure since I started using this laptop with my rig. Any suggestions as to a fix?


locked Re: IC-7300 rig failure #WSJTX_config

neil_zampella <neilz@...>
 

You do realize that you have given us no information about your rig, your OS, or anything else to give you any sort of advice, let alone your callsign and name.

Neil, KN3ILZ

On 5/28/2021 4:03 PM, Peter wrote:

Using wsjt-x version 2.4.0, ft8
 
Any help would be appreciated. I have spent a couple of days making changes with no result. All has been working ok for months before last Windows update.
 
WSJT-X
---------------------------
Rig failure
---------------------------
Hamlib error: Communication timed out
rig_get_freq(2088): freqMainA=0, modeMainA=, widthMainA=0
rig_get_freq(2088): freqMainB=0, modeMainB=, widthMainB=0
rig.c(2090):rig_get_freq return(-5) while getting current frequency
---------------------------



locked Re: #Cat_RigControl PTT Port ERROR happened again #Cat_RigControl

Bill Somerville
 

On 27/05/2021 14:25, jp3exr also ja4lzx wrote:
I was helped PTT port error with rc version in February.
I installed Version 2.4.0 to the version up with on Win10 64bit OS PC yesterday and then I was happened problem when I run WSJTX.
I tried to setting the PTT port but PC said the same error message.
Please tell me error resolution.
Postscript
I installed back to 2.4.0 rc4 version and reboot then I have not error message now.

Bestregard

Taka, JP3EXR
Hi Taka-san,

hardware PTT sharing is working for me with WSJT-X v2.4.0, the hamlib_settings.json file to configure PTT sharing is no longer needed.

The error message you are getting is indicating that another application has the serial port used for PTT open, or perhaps another instance of WSJT-X has set PTT. You can only set PTT from one application at any particular time.

73
Bill
G4WJS.


locked Re: Toggle RRR/RR73 #EnhancementReqest

Jon Ermels
 

If I remember correctly, this software is open source. There are thousands of users that are happy with it.  Just re-write the code if you aren't happy with it.

73 de NØIGU Jon


On Friday, May 28, 2021, 09:16:26 AM CDT, David AD4TJ via groups.io <ad4tj@...> wrote:


Please consider toggling ALT-R for switching from RRR to RR73 instead of 2 seperate keystroke actions. Thanks, David AD4TJ




locked IC-7300 rig failure #WSJTX_config

Peter WR8Z
 

Using wsjt-x version 2.4.0, ft8
 
Any help would be appreciated. I have spent a couple of days making changes with no result. All has been working ok for months before last Windows update.
 
WSJT-X
---------------------------
Rig failure
---------------------------
Hamlib error: Communication timed out
rig_get_freq(2088): freqMainA=0, modeMainA=, widthMainA=0
rig_get_freq(2088): freqMainB=0, modeMainB=, widthMainB=0
rig.c(2090):rig_get_freq return(-5) while getting current frequency
---------------------------


locked Rig failure #WSJTX_config

Peter WR8Z
 

Using wsjt-x version 2.4.0, ft8

Any help would be appreciated. I have spent a couple of days making changes with no result. All has been working ok for months before last Windows update.

WSJT-X

---------------------------
Rig failure
---------------------------
Hamlib error: Communication timed out
rig_get_freq(2088): freqMainA=0, modeMainA=, widthMainA=0
rig_get_freq(2088): freqMainB=0, modeMainB=, widthMainB=0
rig.c(2090):rig_get_freq return(-5) while getting current frequency
---------------------------


locked Re: #GeneralGroupInfo Problem Decoding. #GeneralGroupInfo

Joe Subich, W4TV
 

THERE IS *NO* EXPLICIT B4 COLOR IN WSJTX.

The only color on B4 is any residual color - are all your "decode highlighting" options the same (including the checked options)?

Are you using an eternal program - like JT Alert - on both systems
and is that program configured the same on both systems?

73,

... Joe, W4TV

On 2021-05-28 8:58 AM, Dave Tucker Nu4N wrote:
BK MY ERROR ITS WORKED B4. Red on the windows 7 and green on WIndows 10.Why are the 2 different when both are set the same ??
Thanks 73's de NU4N/Dave


locked Antenna not showing in PSK Reporter #general

 

I noticed today that my antenna's are not showing up in PSK reporter.
Any thoughts ?

--
Thanks 73's de NU4N/Dave


locked Re: Icom 7600 cant get setup right #install

Tim
 

Thank you.  You may be on to something, I need to do some checking I cant do right now, but I will check SWR to ensure 2 to 1 or less as next steps!!!


locked no mike found when starting computer #AudioIssues #FT8

Tim Hollembaek
 

2013 Dell Latitude E6330 laptop
Windows 10 Pro
2.7 ghz processor
8 GB ram
x64 based processor (64 bit)

This laptop has a dual audio jack that is mic/headphones and is the only way to get audio on and out of the laptop.

Rig is a Kenwood TS-830S using the phones jack for audio out and the mike jack for audio in from laptop. I’m using VOX to trigger the rig.

WSJT-X v 2.3.1

I have used the rig with a Linux machine until recently with no problems.

Problem:
At startup with rig attached, the microphone is missing when I look in WSJT-X audio settings and the headphones show connected. The program will toggle the transmitter on but there is nothing being received because of the missing audio input to the laptop. It appears the laptop can’t find the mike unless there is audio coming into it. If I connect a mike/headphone to the jack and test it using Skype’s sound test the test works fine. Then when reconnecting inputs from rig to laptop I find the mike is now connected in the audio tab and WSJT-x works fine. I can then use FT8 for hours with now problems which indicates I am not dealing with some intermittent hardware issue. I have had to do this convoluted start-up procedure since I started using this laptop with my rig. Any suggestions as to a fix?


locked Re: Power slider setting to rig audio level changed a lot from 2.3.1 to 2.4.0 #txaudio

Bob McGraw - K4TAX <rmcgraw@...>
 

I upgraded to 2.4.0 and I'm running Windows 10 Pro.   I saw no change in the PWR slider for either TUNE or Operate.  I do have Remember Tune and PWR settings checked in the F2 menu option. 

73
Bob, K4TAX


locked Re: #Cat_RigControl PTT Port ERROR happened again #Cat_RigControl

Jim Brown
 

I'm a believer in KISS -- Keep It Simple, Stupid!:) If your radio supports VOX from the input you're using to send the digital signal, try that option. I've done nothing but VOX for SSB, RTTY, and WSJT modes for at least 15 years of WSJT modes and heavy duty contesting. K3 since 2008, FT1000MP before that.

73, Jim K9YC

On 5/28/2021 8:39 AM, Sam Sjogren wrote:
I see you have the same serial port specified for CAT Control as well as PTT via RTS.  Is that what you intend to do? Did it work like that before? I've never used such a configuration, personally would use a separate serial device for PTT if I were using hardware keying, but that's the one thing that jumps out at me to ask about.

14981 - 15000 of 40097