On 5 Mar 2017, at 8:32 am, James Quick <n4ule@...> wrote:

Here is what happens when I try to send a CQ, WSJT-X keys the radio and it shows power out, (25w) but I have no tones going out. I am running the Mac Ver. of WSJT-X I don't run Windows at all.

Jim Quick / N4ULE
n4ule@...

On 3/4/17 6:16 PM, Eddy van Keulen via Groups.Io wrote:

Hi Jim,

Besides the audio CODEC, there should also be two virtual COM ports assigned to your radio. One is for CAT control, the other for PTT and CW signalling. These two COM ports should refer to a SiLabs chipset. Does CAT control work? If it does, the PTT will listen to the next or previous COM port, most likely the DTR signal but may also be the RTS.

Regards,
Eddy, W6EDY
--------------------------------------------
On Sat, 3/4/17, James Quick <n4ule@...> wrote:

 Subject: [WSJTX] #new FTDX-3000
 To: WSJTX@groups.io
 Date: Saturday, March 4, 2017, 2:24 PM
   Trying to get the FTDX-3000 to send.
 I can get the sound cart to receive
 but can't get it to send. It shows that I have the USB Audio
 CODEC but
 only the send works. I have installed the right driver for
 the radio but
 no go. I am running WSJT-X on a Mac computer so I need help
 with the mac
 setup. Thanks for all the help getting me this far but I
 still need a
 little help. Thanks for any help or advice.
   73
     --
 Jim Quick / N4ULE
 n4ule@...
         

On 3 Mar 2017, at 10:57 pm, Robert Nobis <N7RJN@...> wrote:

Jim,

I have a similar set-up but with an ELecraft K3.  But I use WSJT-X to control the rig, rather than MacLoggerDX. Also, I use VOX to initiate transmitting.

Bob Nobis 
n7rjn@...

On Mar 3, 2017, at 07:43, James Quick <n4ule@...> wrote:

Just got a new FTDX-3000 radio and need some help setting it up on my Mac computer. I am running,

Mac Mini,

MacLoggerDX,

WSJT-X v1.7,

JT-Bridge.

I have MacLoggerDX controlling the radio. I can get WSJT-X to receive but can't get it to transmit. Thanks for any help or advice.

73


-- 
Jim Quick / N4ULE
n4ule@...

Hi Jim,

Besides the audio CODEC, there should also be two virtual COM ports assigned to your radio. One is for CAT control, the other for PTT and CW signalling. These two COM ports should refer to a SiLabs chipset. Does CAT control work? If it does, the PTT will listen to the next or previous COM port, most likely the DTR signal but may also be the RTS.

Regards,
Eddy, W6EDY
--------------------------------------------
On Sat, 3/4/17, James Quick <n4ule@...> wrote:

Subject: [WSJTX] #new FTDX-3000
To: WSJTX@groups.io
Date: Saturday, March 4, 2017, 2:24 PM
Trying to get the FTDX-3000 to send.
I can get the sound cart to receive
but can't get it to send. It shows that I have the USB Audio
CODEC but
only the send works. I have installed the right driver for
the radio but
no go. I am running WSJT-X on a Mac computer so I need help
with the mac
setup. Thanks for all the help getting me this far but I
still need a
little help. Thanks for any help or advice.
73
--
Jim Quick / N4ULE
n4ule@...

Hi Jim,

Besides the audio CODEC, there should also be two virtual COM ports assigned to your radio. One is for CAT control, the other for PTT and CW signalling. These two COM ports should refer to a SiLabs chipset. Does CAT control work? If it does, the PTT will listen to the next or previous COM port, most likely the DTR signal but may also be the RTS.

Regards,
Eddy, W6EDY
--------------------------------------------
On Sat, 3/4/17, James Quick <n4ule@...> wrote:

Subject: [WSJTX] #new FTDX-3000
To: WSJTX@groups.io
Date: Saturday, March 4, 2017, 2:24 PM
Trying to get the FTDX-3000 to send.
I can get the sound cart to receive
but can't get it to send. It shows that I have the USB Audio
CODEC but
only the send works. I have installed the right driver for
the radio but
no go. I am running WSJT-X on a Mac computer so I need help
with the mac
setup. Thanks for all the help getting me this far but I
still need a
little help. Thanks for any help or advice.
73
--
Jim Quick / N4ULE
n4ule@...

On Mar 3, 2017, at 07:43, James Quick <n4ule@...> wrote:

Just got a new FTDX-3000 radio and need some help setting it up on my Mac computer. I am running,

Mac Mini,

MacLoggerDX,

WSJT-X v1.7,

JT-Bridge.

I have MacLoggerDX controlling the radio. I can get WSJT-X to receive but can't get it to transmit. Thanks for any help or advice.

73


--
Jim Quick / N4ULE
n4ule@...

On Jan 15, 2017, at 6:33 AM, Bill Somerville <g4wjs@...> wrote:

On 15/01/2017 05:00, Andrew O'Brien wrote:
Just FYI, the most recent release of WSJTX did not contain the full Hamlib support for a Flex 6300. The Flex 6500 and 6700 work fine but not the TCP support for the 6300. I have beenadvised the issue is fixed for future updates. I think the issue was an omission by the hamlib folks, not the WSJTX team.

Hi Andy,

that is not the full story. WSJT-X includes a statically linked version of Hamlib, we do that so we can get the very latest Hamlib support and features, we have never taken out or dropped any support.

The support in Hamlib for the FlexRadio Power and Smart SDR software where it emulates a Kenwood TS-2000 has been in place for some time and it gives enough support for basic WSJT-X operation.

The Hamlib support for the network CAT control of SmartSDR gets little love and needs attention. If FlexRadio users or FLexRadio themselves need better support for this protocol then someone with the relevant programming skills and the relevant proprietary software and hardware needs to do the work.

Both Hamlib and WSJT-X are open source projects and they rely on users contributing patches.

The change you are referring to is that the identification returned by SmartSDR when emulating a TS-2000 over a serial port and running a FlexRadio 6300 has been added so the existing TS-2000 driver will recognize that set up. It does not specifically add any support it just allows that existing set up to be used with the existing support for the 6500 and 6700.

73
Bill
G4WJS.