1. Messages
  2. MS update sent my Silicon Lab Ports and CODEC files into Hidden.

locked Re: MS update sent my Silicon Lab Ports and CODEC files into Hidden.

Herb Blue - WB8ASI
 

Try Goggling IC-7610 SuperSpeed-FIFO Bridge:

The communications are done through FTDI's "D3XX Driver."
You need to install the driver (USB I/Q Package for HDSDR) that can be downloaded from Icom web site.
After the driver is installed, you can receive I/Q signals and control the IC-7610 through the D3XX Driver,
using an I/Q receive software (user supplied).
To receive I/Q signals and control the IC-7610 from the user application, you need FTDI's "FTD3XX.dll." Refer
to "D3XX Programmer's Guide" that can be downloaded from FTDI web site on how to use the functions.
You need to set the device description and appropriate "endpoint." Refer to the next topic for details about
them.

D About the Device Description

The Device Description, that is needed to open the [USB 2] port, is shown below.
“IC-7610 SuperSpeed-FIFO Bridge”

73 Herb WB8ASI

On May 12, 2020 at 11:54 AM Bubba Tim <timreyes@...> wrote:

Hi Jerry,

Thanks for your help.  I plugged in a flash dive, the laptop (LP) gave the audible connection sound, but no COM Ports were showing in the Device Manager. Did the same with IC 7610, got the sound, but showed up in Other devices as IC-7610 SuperSpeed-FIFC Bridge, with an error, "the drivers for this device are not installed (Code 28) To find driver, click update driver. After clicking Update, it searched my computer and the internet and could not find anything. I have uni stalled and reinstalled WSJTX many times with no luck.  I will contact MS and see what they say.  

73
Thanks

Bubba Tim
Hero of small cats and defender of undersized lobsters
www.bubbatim.com
 
From: WSJTX@groups.io <WSJTX@groups.io> on behalf of jwvaughn via groups.io <jwv_not@...>
Sent: Tuesday, May 12, 2020 11:33 AM
To: WSJTX@groups.io <WSJTX@groups.io>
Subject: Re: [WSJTX] MS update sent my Silicon Lab Ports and CODEC files into Hidden.
 

If the com ports are hidden in the device manager that means that the device has not been detected.  I would suggest:

1.     Try a different USB port

2.     Try the device on a different computer

3.     Try a different cable

4.     Try a different device, perhaps a thumb drive, on the problem computer’s USB ports

 

Even if the wrong drivers are loaded, the device should show up in device manager so it is more likely a hardware problem than a software problem.

 

Jerry

 

From: WSJTX@groups.io [mailto:WSJTX@groups.io] On Behalf Of Bubba Tim
Sent: Tuesday, May 12, 2020 05:26
To: WSJTX@groups.io
Subject: Re: [WSJTX] MS update sent my Silicon Lab Ports and CODEC files into Hidden.

 

That most of the issue. COM Ports do not show up in the Device Manager. You can only see them in the "Hidden" files.

 

Bubba Tim

Hero of small cats and defender of undersized lobsters

www.bubbatim.com

From: WSJTX@groups.io <WSJTX@groups.io> on behalf of Tom Melvin <tom@...>
Sent: Tuesday, May 12, 2020 7:54 AM
To: WSJTX@groups.io <WSJTX@groups.io>
Subject: Re: [WSJTX] MS update sent my Silicon Lab Ports and CODEC files into Hidden.

 

Hi

 

Does the Windows Device Manager  show the adapter when plugged in - tried a different USB port ?

 

Tom

 

--
73

Tom
GM8MJV (IO85)



 

On 12 May 2020, at 12:39, Bubba Tim <timreyes@...> wrote:



Hamlib error: IO error while opening connection to rig. The CAT Control only gives me the option of USB and does not list any COM Ports.

 

Bubba Tim

Hero of small cats and defender of undersized lobsters

 

From: WSJTX@groups.io <WSJTX@groups.io> on behalf of Tom Melvin <tom@...>
Sent: Tuesday, May 12, 2020 4:22 AM
To: WSJTX@groups.io <WSJTX@groups.io>
Subject: Re: [WSJTX] MS update sent my Silicon Lab Ports and CODEC files into Hidden.

 

What was the ‘config error’ ?

 

Tom

 

--
73

Tom
GM8MJV (IO85)



 

On 11 May 2020, at 22:08, Bubba Tim <timreyes@...> wrote:



I was working FT8 this past Sat in the morning. I took a break and came back into the shack and tried to make a contact.  Noticed no power was being sent. Then I got a config error.  I am sure this is a MS issue. Other than a complete reformat of my lab top, any thoughts?  And if I do a reformat, how can I keep this from happening again? I have tried to move back the hidden files, but ran into issue of the computer not connecting to the files. I have been working on this for 3 days. If this was not a new computer, I would just buy another... 

 

 

 



 

Join main@WSJTX.groups.io to automatically receive all group messages.