locked Re: 2.3.0 TX No Audio after Band Change #FT8 #AudioIssues


Derek Brown
 

Hi Neil,

It does it if I select Tune, transmits a carrier, de-select Tune, stops TX, on RX, say someone is calling CQ, klick on their callsign, WSJT poplates the various boxes, goes to TX at the right time - No Tones, no TX output, nothing !!!

Derek G8ECI

On Monday, 22 February 2021, 19:48:30 GMT, neil_zampella <neilz@...> wrote:


Try using 'Halt Tx' button rather than use the Tune button as a toggle.

Neil, KN3ILZ

On 2/22/2021 12:58 PM, Derek Brown via groups.io wrote:
Hi all,

I had a similar problem on Ver 2.3 this afternoon using a IC-9700, if I hit Tune I get a tone out , if I then went enable tx and call CQ, radio would click over to TX, but no tone sent, no RF from 9700, in USB-D1 and all connectors correct, rebooted PC no change, checked Com port settings all OK, I run HRD and then use that to CAT control WSJT-X, checked Audio settings in WSJT-X - RX ok, and TX looked ok. in then end it seemed to start working again. Will try and see if it does it again later and note steps taken to restore normal functionality.

73 Derek G8ECI.

On Monday, 22 February 2021, 16:16:13 GMT, Robert Lorenzini <bob@...> wrote:


Anan7000dle
PowerSDR OpenHPSDR mRX PS v3.4.9
Band change by WSJT-X v 2.3.2

Reverted to 2.2.2 and the feature is gone.
I also would get a report of my own station with 30db report after
some time even with band change.

Bob - wd6dod

On 2/21/2021 10:35 PM, Reino Talarmo wrote:

Hi Bob,

Starts to be interesting. For records which rig, program version, Radio, General settings and perhaps how exactly band change is operated may be needed before this behavior can be repeated.

 

73, Reino OH3mA

 

From: main@WSJTX.groups.io [mailto:main@WSJTX.groups.io] On Behalf Of Robert Lorenzini
Sent: 21. helmikuuta 2021 21:44
To: main@WSJTX.groups.io
Subject: Re: [WSJTX] 2.3.0 TX No Audio after Band Change #FT8 #AudioIssues

 

I can confirm the OP's report. I have exactly the same problem with CAT
keying. The rig keys up but no audio after band change tune or tx. Halt and
tx restores mostly.

Bob - wd6dod

On 2/21/2021 9:50 AM, Randy Reynard wrote:

Answers to the questions - and / or comments:

 Do you Stop monitoring and Halt Tx before a band change?
> No,  I didn't need to stop monitoring in prior versions.  I never change bands during a TX so the 2nd part of that question doesn't apply.

> The RFI question doesn't apply because I'm never transmitting when this happens.  The PTT method I use is CAT. The radio goes into TX with no issues, but there's just no audio.

R: So after changing the band you have received a full timeslot to spot somebody and double-clicked his call, I assume. And your Tx has gone to transmit at the beginning of next appropriate TX cycle, but no audio. After noting that you use “halt Tx” and “Enable Tx” and still no audio. Or did I missed something? Or do you have “Double-click on call sets Tx enable” unticked and you use “Enable Tx” to invoke transmission?
>Your assumption is correct.  I'm waiting for a callsign to show up - after a decode - than double clicking on it to initiate a response, and yes during the beginning of an appropriate TX cycle.   The second part of your question is no longer valid, as I've discovered that a "halt/enable" cycle does restore audio during TX.

Does this “no audio after band change” happen also, when you try to send a CQ in the next available Tx period after band change? I assume that there is no confusion about “Tx even/1st “ and which time-slot is used for transmission.
> I don't know, because I always listen for other stations and respond after a band change.  I understand the "TX even/1st" concept.   I've been using this program for well over a year and haven't had any issues until 2.3.0.

I have assumed that audio is sent at the same time as CAT has commanded PTT on. By the way which PTT method you are using and which rig we are talking about? We have some unknown issue in your system.
>As I have answered or provided before, I am using CAT control to command PTT.  The rig is an ICOM 7300, I now know of at least 3 other 7300 owners with the same issue, as well as Yaesu and other ICOM models.  Others i have contacted agree that nothing changed in their setup except to upgrade to 2.3.0.  They can all restore the transmitted audio by doing a "halt/enable" cycle.

I appreciate your interest and support - I hope my answers are understandable.

W0RDR



  
  
  

 









  



Join main@WSJTX.groups.io to automatically receive all group messages.